Page 3 of 3 FirstFirst 123
Results 21 to 24 of 24

Thread: Chameleon Technology ALC60x PSU problem, help?

  1. #21
    Join Date
    Jun 2008
    Location
    Yellowknife, NT, Canada
    Posts
    2,147,484,113

    Default

    It's either LED3 or LED2 that comes on, I won't know until the weekend when I'll have time to fire it up. They are right beside each other, and one of them comes on for sure, but which one I'm not sure of.

    I'll check at the weekend, hopefully I can fix it without a scope. How much was the cheap scope from maplins?

    thanks for the help

  2. #22
    Join Date
    Jan 2008
    Location
    South Lincs, UK
    Posts
    2,625

    Default

    This does seem very odd as it has never skipped a beat while I had it.
    Did you do anything to it Adam?

    It has ran many many times here and all day at most LEM's.
    Are you sure it's not the controller before you go diving into the PSU Adam?

    Unless it suffered something during transit?

    It's very odd
    --------------------
    My Brain urt's!

    Continuously in Awe! of (H)Al, the Photonlexicon Font of Complete Knowledge - The (H)Al'PL Database of complete puss that no one needs to know or ever trusts as he ain't really got a Scooby doo about now't!

  3. #23
    Join Date
    Jun 2008
    Location
    Yellowknife, NT, Canada
    Posts
    2,147,484,113

    Default

    Quote Originally Posted by smogthemog View Post
    This does seem very odd as it has never skipped a beat while I had it.
    Did you do anything to it Adam?

    It has ran many many times here and all day at most LEM's.
    Are you sure it's not the controller before you go diving into the PSU Adam?

    Unless it suffered something during transit?

    It's very odd
    I took it apart and replaced that line capacitor with one identical to it. It could be that it got damaged while I was replacing that. It could also be my higher line voltage that's caused it.

    It was running fine and then it winked out, so that would suggest that it's my line voltage or some damage to a component caused by the capacitor repair that just needed some power to completely die. It's not the controller - everything comes on as it should, and the operate relay does tick over ( I can hear it, and the laser wouldn't try to start if it didn't turn on).

    I doubt it was due to damage in transit - everything was operating fine when it arrived, I didn't even discover the capacitor till I took it apart to install the colour card.

    It was either a fault of my own or a fault caused due to my line voltage being higher than normal UK voltages. Whatever it is, I look forward to fixing it. I've been looking for something to do for ages!

    On another note : LED 3 comes on when the operate relay is on, all other LEDs are also on at all times. I'll check the voltage on the "HV bus" later at some point, I don't have time right now. Oh, and I need to find it!

    I've also checked the fuses and they are both a dead short.

  4. #24
    Join Date
    Jun 2008
    Location
    Yellowknife, NT, Canada
    Posts
    2,147,484,113

    Default

    Okay, tore everything apart tonight. been looking at the schematics and as far as I can tell it's either the MOSFETs or something after them. I'm going to put it back together and work on it throughout the week.

    I checked the Relay and the coil seems fine, during the week i'll check that it actually does close properly. If it does then I'll move on to testing the MOSFETs. Also, I noticed that R22 is missing, is this component needed?

    I know it's nothing before the gates of the MOSFETs as the gate drive LED comes on. It's either before the source on the MOSFET , at the MOSFETs or after the MOSFETs. So far looks good!

    More updates to come later!

    Cheers!.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •