Results 1 to 4 of 4

Thread: Another strange modulation issue - RGY rebuild

  1. #1
    Join Date
    Mar 2010
    Location
    Germany
    Posts
    19

    Default Another strange modulation issue - RGY rebuild

    Hi PL and again another question from the beginner,

    today I opened one of my G-Tech ("Highlase") 100mW (G) TTL ILDA Projectors and combined the green 100mW one with an about 50mW red TTL from an old G-Tech 120rgy DMX Projector I bought one year ago. This was no problem and worked fine, now I have an RGY controllable via ILDA. I used the psu from the old DMX projector as a power supply for the red one, the TTL signal comes from the ILDA card used in the Highlase. After removing the jumpers from the jacks labeled "R" "G" and "B", the setting was working properly and all 3 colours are accessible now.

    After this little success, I decided to do a second rebuild with another Highlase (same specs) and combined a 150mw red TTL module from an LW EL 200rgy DMX. A also used the psu in the same kind from the DMX projector. And here is the problem: When I fire the "new" projector up, only the green laser works properly, the red one keeps blanked when attached to the ttl jack from the ILDA card. If I remove the jack, the red diode keeps burning even when it shouldn't (e.g. direct after switching the unit on). I don't think that the isolation of the wires or the housing would be a problem, as I read in another thread about the cheap chinese ttl modules. Is it possibly perhaps that the red one only works properly with the "combined DMX/TTL driver board" from the old DMX projector? Any ideas? Thanks for help, greetings from Germany and please excuse my bad english...

  2. #2
    Join Date
    Mar 2006
    Location
    Ottawa, Ontario, Canada
    Posts
    494

    Default

    Quote Originally Posted by Nevermind29 View Post
    Hi PL and again another question from the beginner,

    today I opened one of my G-Tech ("Highlase") 100mW (G) TTL ILDA Projectors and combined the green 100mW one with an about 50mW red TTL from an old G-Tech 120rgy DMX Projector I bought one year ago. This was no problem and worked fine, now I have an RGY controllable via ILDA. I used the psu from the old DMX projector as a power supply for the red one, the TTL signal comes from the ILDA card used in the Highlase. After removing the jumpers from the jacks labeled "R" "G" and "B", the setting was working properly and all 3 colours are accessible now.

    After this little success, I decided to do a second rebuild with another Highlase (same specs) and combined a 150mw red TTL module from an LW EL 200rgy DMX. A also used the psu in the same kind from the DMX projector. And here is the problem: When I fire the "new" projector up, only the green laser works properly, the red one keeps blanked when attached to the ttl jack from the ILDA card. If I remove the jack, the red diode keeps burning even when it shouldn't (e.g. direct after switching the unit on). I don't think that the isolation of the wires or the housing would be a problem, as I read in another thread about the cheap chinese ttl modules. Is it possibly perhaps that the red one only works properly with the "combined DMX/TTL driver board" from the old DMX projector? Any ideas? Thanks for help, greetings from Germany and please excuse my bad english...
    Hi,

    I'm not familiar with the laser devices mentioned above . Many Chinese laser manufacturers design their lasers so when nothing is connected (floating TTL input) the laser outputs a beam. This is probably so customers can't complain it doesn't work when they first power it up. In my humble opinion,the laser should only be "ON" when a TTL high 5 vdc signal is present for safety reasons alone. Perhaps your laser driver is inverted (needs TTL low be to "ON").

    Rick
    Profile Redacted by Admin @ 04.24.2010

  3. #3
    Join Date
    Dec 2008
    Location
    Southport, UK
    Posts
    2,746

    Default

    Assuming your DAC has low output impedance and you only need TTL control, you might resolve the issue by tying the blanking input to ground with a 1K resistor.
    http://img62.imageshack.us/img62/3985/laser.gif

    Doc's website

    The Health and Safety Act 1971

    Recklessly interfering with Darwin’s natural selection process, thereby extending the life cycle of dim-witted ignorami; thus perpetuating and magnifying the danger to us all, by enabling them to breed and walk amongst us, our children and loved ones.





  4. #4
    Join Date
    Mar 2010
    Location
    Germany
    Posts
    19

    Default

    Thanks again PL, switching the polarity of the ttl jack solved the problem !

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •