Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 22

Thread: Stabilite 2017

  1. #11
    Join Date
    Apr 2010
    Location
    Northridge,CA
    Posts
    12

    Default

    Both photos are of the same thing,output from the laser taken against a white backing about a foot away. One was taken in darkness, one in light. Nothing is adjusted or aligned. This is the first run of the laser. The laser housing is missing the lens on the front, but I am not sure if that lens does anything, or is just a cover.
    Mike

  2. #12
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    Shoot me a pic, it sounds like your missing a OC mirror. BTW, when lasing, these are not toys. Do you have goggles?

    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  3. #13
    Join Date
    Apr 2010
    Location
    Northridge,CA
    Posts
    12

    Default

    I do have a set of glasses made for Argon and KTP lasers. I think they are 190-532 nm. The stabilite 2017 laser came in Argon and Krypton. When I bought it, it didnt specify which it was.
    I also purchase a used closed cooling system for next to nothing, but it didnt have enough flow to turn the sensor and allow the laser to operate. This laser requires 2.2 gpm flow, so I need to upgrade the pump (this sucker must get hot to require that much flow). I can temporarily operate with a standard water hose.

    I attached a picture of the front, where the cover is missing.laser2..jpg
    Mike

  4. #14
    Join Date
    Jun 2008
    Location
    Yellowknife, NT, Canada
    Posts
    2,147,484,113

    Default

    Yeah they do need quite a bit of water. You're probably looking at around 8-10kW of heat or more!

  5. #15
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    OK, sad news, your missing the front optics mount and the magentic front cover. This is not a death sentence, there are workarounds, ie mounts are easily made and I have tonnes of argon/krypton optics. Rear plate photo please... and photo with head top cover off...

    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  6. #16
    Join Date
    Apr 2010
    Location
    Northridge,CA
    Posts
    12

    Default

    Actually, Zorg has the exact same laser as I do, and funny enough it looks like his is missing the front optics and cover as well. Here are the pictures of his, which are exactly the same as mine shown below.
    http://www.flickr.com/photos/3076128...7607454311955/
    Thanks again for the help,
    Mike

    laser..jpg

  7. #17
    Join Date
    Apr 2010
    Posts
    1

    Default

    Hello,
    I have the same laser and we're trying to make it work. Sorry for a stupid question, but could someone please tell me which one of the pipes in the head is water in and which one return, e.g. does the water pass first through the tube or the flow meter?
    Thanks,
    Liisa

    Edit: Sorry just realised there are arrows in the flow meter... For some reason the flow meter just isn't working...
    Last edited by liisa; 04-29-2010 at 03:28.

  8. #18
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    As far as I can tell, unless some optics are missing, all Mike needs to do is align his.

    He needs to read the ion laser alignment chapter in Sam's faq and take a look at this thread

    for some ideas: http://www.photonlexicon.com/forums/...07-35-mw-He-Ne.

    He'll need acetone and methanol, lab or spectroscopy grade, a few ounces of each.

    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

  9. #19
    Join Date
    Jun 2010
    Posts
    1

    Default stabilite 2017 mirrors

    hi guys,

    I'm trying to get one of these lasers up and running myself. The system I have is an argon system I believe, with the UV mirrors. I want to run it in multiline or single-line visible mode. Does anyone have the visible mirrors for this laser? I believe they are newport part numbers G0302-001 for the output coupler and G3802-009 for the high reflector. Also, does anyone have the prism assembly for this unit?

    thanks!
    Mark

  10. #20
    mixedgas's Avatar
    mixedgas is offline Creaky Old Award Winning Bastard Technologist
    Infinitus Excellentia Ion Laser Dominatus
    Join Date
    May 2007
    Location
    A lab with some dripping water on the floor.
    Posts
    10,114

    Default

    [QUOTE=wmbates;149468]hi guys,

    I'm trying to get one of these lasers up and running myself. The system I have is an argon system I believe, with the UV mirrors. I want to run it in multiline or single-line visible mode. Does anyone have the visible mirrors for this laser? I believe they are newport part numbers G0302-001 for the output coupler and G3802-009 for the high reflector. Also, does anyone have the prism assembly for this unit?

    end quote.

    I have similar mirrors but no prism.

    PM me.

    Steve
    Qui habet Christos, habet Vitam!
    I should have rented the space under my name for advertising.
    When I still could have...

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •