Page 4 of 5 FirstFirst 12345 LastLast
Results 31 to 40 of 43

Thread: LFI Player + DAC problem

  1. #31
    Join Date
    Jun 2010
    Posts
    19

    Default

    Yes, CA3140N was exposed to negative voltage, did I damage chip?

  2. #32
    Join Date
    Jul 2008
    Posts
    822

    Default

    Quote Originally Posted by ReNNo View Post
    Yes, CA3140N was exposed to negative voltage, did I damage chip?
    According to the data sheet, the CA3140N only tolerate -0.5V, if you go more negative it
    can be damaged.

    Dean

  3. #33
    Join Date
    Jun 2010
    Posts
    19

    Default

    OK, I'm going to make another PCB but I'm going to use only one opamp.
    Is there anything else that I should care about?

  4. #34
    Join Date
    Jul 2008
    Posts
    822

    Default

    Quote Originally Posted by ReNNo View Post
    OK, I'm going to make another PCB but I'm going to use only one opamp.
    Is there anything else that I should care about?
    You should try to fix the board you have first. If you decide to build another, try
    building it on a breadboard before you build a new one.

    Dean

  5. #35
    Join Date
    Jun 2010
    Posts
    19

    Default

    I made another PCB, this time I didn't use additional op-amp and now blanking works



    But here is another problem. When I play some ILD files I can hear crackling from galvos and this results some random lines on projected image.
    But this is not opamp or galvos related problem because I can hear these crackling sounds on headphones. Can this be problem with LFI player or sound card drivers?

    Another thing...
    Looks like blanking doesn't work very well. There are some unwanted lines.




    Click on thumbnail to see video:


    I think that all these problems are related to these crackling sounds from sound card, what do you think?
    Is there any other ILDA file player that is compatible with CM106?

    btw, here is ILDA test file:



    EDIT:

    Can someone tell me which drivers should I use and how to correctly configure drivers settings?
    Last edited by ReNNo; 02-22-2011 at 06:33.

  6. #36
    Join Date
    Jul 2008
    Posts
    822

    Default

    Good to see that you are making progress, I'm impressed with your board construction!

    As for the crackling problem, you could try my SpiroDAC program for testing your hardware; it generates pure sine waves of adjustable frequencies and levels. SpiroDAC uses the same AudDAC driver as LFI Player.

    http://laserboy.org/lwave/


    Dean

  7. #37
    Join Date
    Jun 2010
    Posts
    19

    Default

    I think that your program has just gave me a clue of what my problem might be.

    Take a look at this video:



    When I set blanking at 13Hz you can see that projected image is not very accurate.
    At 1Hz blanking you can easily see that projected image is moving from upper right corner to lower left corner as laser is turning off/on. And when I turn off blanking image is very accurate. I power up laser diodes and op-amps from the same PC power supply. What I can say is that turning laser on results voltage drop on 12V rail and op-amps change their output voltage. What do you think?
    I think that I should try with another better quality PSU.

    And about crackling sounds... yes,I heard them but much less than when I use LFI player. But even in LFI player it depends from what ILDA file I play.
    I definitely need to configure sound card setting or use correct drivers but I don't have idea which drivers to use. At the moment I use 6.12.8.2131 that are compatible with Windows 7 x64.

  8. #38
    Join Date
    Oct 2006
    Location
    Cleveland, Ohio
    Posts
    2,342

    Default

    I'm surprised you were able to get it working with windows 7 at all. To try to reduce crackling you might want to adjust the
    LowLatencyBuffering=no
    RepeatFrameWhenOut=yes

    settings to see if it improves anything.

  9. #39
    Join Date
    Jun 2010
    Posts
    19

    Default

    I did that but there is no improvement at all.

    EDIT:
    I've just tried with Corsair HX620 and nothing changed. Voltage of 12V rail was very stable.
    I need to install virtual machine and try with windows XP, I'll let you know if it helped.

    EDIT2:
    Windows XP didn't solve my problems. There are still crackling sounds and projected image is still moving as lasers turn on/off.
    Here is output sound that I recorded:
    http://www.mediafire.com/?ntmvah999d744c0

    I'm not worried too much about this crackling sounds but I'm worried that projected image is moving as I turn on/off lasers. Thats is most likely cause of all these problems.
    What I'm supposed to do? Any ideas?
    Last edited by ReNNo; 02-23-2011 at 11:21.

  10. #40
    Join Date
    Jul 2008
    Posts
    822

    Default

    I have been looking at Benm's original print.

    http://laserpointerforums.com/attach...ser-driver.jpg

    Do you have an extra power supply to provide the +12V independently to the laser diode as his print suggests? There may be a power supply interaction problem that could be fixed...

    SpriroDAC may produce crackling sounds when adjusting the sliders, because the program gets interrupted during that process, but it should be clean any other time.

    Dean

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •