Results 1 to 10 of 10

Thread: Is this possible?

  1. #1
    Join Date
    Nov 2011
    Location
    Bedfordshire, UK
    Posts
    603

    Default Is this possible?

    First, apologies for rough post, but posting from my phone...

    I've had an idea for a look for a client and before I put it to them was wondering about the logistics/physics being actually possible.

    Without going into too many details, It would require producing a sheet of light that is parralel (or as near as possible) down both edges, so probably not a scanned beam.
    Would a line of 20/80% reflect dicros work to produce this?
    Or is there an easier, existing way to do this that I've not seen/heard about being such a laser n00b? :-)

    Your help here muchly appreciated! :-)
    Thanks PL
    If in doubt... Give it a clout?

  2. #2
    Join Date
    Feb 2010
    Location
    Melbourne, Australia
    Posts
    1,106

    Default

    Not 100% sure of what you're after as the details are a little scant, but... What about 2 scanned beams? You could match the angles of each to create each of the edges you want parallel. You would end up with some overlap, but you could angle the projectors to match up.

  3. #3
    Join Date
    Dec 2007
    Location
    Nottingham, UK
    Posts
    2,849

    Default

    What power and how many sheets?
    If it is low, how about just a simple linear array of diodes with line generating optics in it? You could make some tiny modules and just clamp them wherever on your truss. Maybe go nuts with a simple DMX driver... depends on the client budget I guess.
    - There is no such word as "can't" -
    - 60% of the time it works every time -

  4. #4
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    Dan, wouldn't the line expand from each source though in a cone?
    So even in combination, at some point in the distance they will start to overspill the edge boundaries set by the 2 on each end (I'm assuming these would be angled inwards s that the outer edge ran parallel with the opposite one)

    Sort of like this

    |/VVVVVVVVVVVV\|
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  5. #5
    Join Date
    Dec 2007
    Location
    Nottingham, UK
    Posts
    2,849

    Default

    Adam,
    I'm not getting what you mean; 36 hours and no sleep makes Dan a little slow.
    - There is no such word as "can't" -
    - 60% of the time it works every time -

  6. #6
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    Well I'm reading that Wookie wants to do a beam like this:

    ___________________________________




    ___________________________________


    So if you made it up of an array of diodes with line generators, the line generators I've seen do not do a parallel beam, they do a fan. So lots of little fans in an array will look like this at the source:

    <
    <
    <
    <
    <
    <

    You could get the outside edges parallel by turning the diodes on the outside edges inwards, but then they would cross fire and go over the other side. And the ones in the middle or the array would eventually expand outside of the outer edges too.

    Unless I'm misunderstanding what Wookie is trying to do.
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  7. #7
    Join Date
    Nov 2011
    Location
    Bedfordshire, UK
    Posts
    603

    Default Some clarification...

    Hi All.

    OK, so for clarification, Norty has got it pretty close.

    I'm after a beam :-

    _____________________________________



    _____________________________________

    like that but 1 or 2 mm thick by 20 to 40cm wide.

    Taggalucci's idea might work as the beam distance would only be a few meters before it was masked in the rig, and setting it up would be fairly simple as ideally it would be tourable... But it might lose a little bit of beam at the projector end before the beams overlap.

    Sort of :-

    :____________________________________
    :\....../
    :.\..../
    :..\../
    :...\/
    :.../\
    :../..\
    :./....\
    :/......\
    :___________________________________

    I like Mr Briggs Idea as well, as I could possibly customise a cheap LED batten fixture by replacing the LEDs for Laser Diodes, but I think Norty hit the nail on the head there by saying the beam alignment and overlap might not be quite what I'm after.

    Anyone got any more ideas?
    Last edited by WookieBoy; 05-01-2012 at 11:38. Reason: Putting . in diagram to make it format correctly :(
    If in doubt... Give it a clout?

  8. #8
    Join Date
    Aug 2008
    Location
    UK
    Posts
    5,704

    Default

    Quote Originally Posted by taggalucci View Post
    Not 100% sure of what you're after as the details are a little scant, but... What about 2 scanned beams? You could match the angles of each to create each of the edges you want parallel. You would end up with some overlap, but you could angle the projectors to match up.
    That's what I would have thought. 2 projectors 1 at each end of the room projecting a fan say 20cm wide and then adjusted for angle so they match up and appear parallel.

    Like this:




    You could probably adjust the angle in the software rather than mount the projectors unsquare.

    Also, you needn't worry about the shape of the ends because in reality they're cut off by the wall at each side.

    Only problem is going to be the width you want due to the angles the fans will have to be to make the sides parallel. 40cm is very narrow over a rooms width.

    I wonder if you could restrict the width using masking?
    Last edited by White-Light; 05-01-2012 at 15:52.

  9. #9
    Join Date
    Sep 2006
    Location
    Netherlands
    Posts
    1,438

  10. #10
    Join Date
    Nov 2007
    Location
    SoCal / San Salvador / NY
    Posts
    4,018

    Lightbulb

    Hiya Wook..

    Quote Originally Posted by WookieBoy View Post
    Anyone got any more ideas?
    Why not use a crystal-clear glass-rod - ie, like a pyrex 'stirring-rod', etc - in front of your diode - (..which will give you a very-wide / near-180˚ 'line'..) - and then, 'barn-door' it, with 2 'L's at the 40cm-extremities? ie: (the "u" is the diode, "o" is the rod, end-view.. you'll have to 'fill in the blanks' with imagination-dust..

    ****u****
    ooooooooo
    |||||^|||||
    |OOOOOO|
    |OOOOOO|
    |OOOOOO|

    ..ya gotta love trying to use ASCII to 'draw', eh? Lol...

    Just a thought... feel-free to riddle it full of holes..
    cheers..
    j
    ....and armed only with his trusty 21 Zorgawatt KTiOPO4...

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •