What would be a good balance of wavelengths for a rgb laser.. Could you also give the power you would think would be appropriate... I am shooting for a 900-1500mw power range..
What would be a good balance of wavelengths for a rgb laser.. Could you also give the power you would think would be appropriate... I am shooting for a 900-1500mw power range..
300-350mW 637nm red
500mW 445nm blue
500mW 532nm green
will give you powerful and accept balance within your expect power range
Laser-wave can supply:
Green 532nm, 4W, 10W, 15W
blue 445nm, 2W, 3.5W, 6W, 10W
blue 462nm, 2W
Red 638nm, 500mW, 1W,2W, 4W, 5W, 6W, 8W, 10W
All diodes, All optics, All mount, All laser base and housing for yourselves building lasers.
Speical products, 532nm, OEM-V-SS, 4W, 98mm*46mm*48mm; OEM-H, 10W, 250mm*88mm*70mm
www.laser-wave.com or www.laser-wave.net
bridge@laser-wave.com or 463366312@qq.com
We Chat: 463366312, Laserwave-Bridge
Hi
If you do a search of the forum you'll see that this very subject has been addressed literally hundreds of times. Warning... Some of the posts can be quite emotive, particularly where a certain piece of software is invoked ((<cough> Chroma <cough>)
The answer also depends on how many different wavelengths of laser you want to have in your projector. Most people settle on three colours and attain an excellent white balance, some projectors have perhaps five or more different wavelengths in an effort to expand the colour gamut. It really depends on how much cash you have to sink into the bottomless pit of this hobby
Throw the different beam profiles of all the lasers into the mix just to complicate it even further. Having said all that we almost exclusively use 532nm DPSS for our green, and since the advent of reasonably priced blue diodes, most seem to settle on 445nm for the blue. Red is a little more difficult and you have more choice of wavelengths, anything from 635nm up to 660nm. Obviously, and usefully, you need less power (to acheive the same perceived brightness) from the 635nm end of the scale than you do at the 660nm end of the scale. However, using 660nm will extent the colour gamut somewhat.
Hehe... Nothing in this hobby is quite straightforward... Welcome to the world of lasers. Have fun
Jem
P.S. Almost forgot... If you're mixing DPSS lasers and Diode lasers you'll almost certainly want some form of colour correction circuitry in there to balance out the rise and fall times of the different lasers. Contact Rob AKA 'Stanwax' here on the forum.
Last edited by Jem; 10-24-2012 at 03:27.
Quote: "There is a theory which states that if ever, for any reason, anyone discovers what exactly the Universe is for and why it is here it will instantly disappear and be replaced by something even more bizarre and inexplicable. There is another that states that this has already happened.”... Douglas Adams 1952 - 2001
Ditto to what Jem said. Beautifully put. Everyone has their own opinions as you'll find out if you're around enough but, based on my own experience, while bridge is close, I'd go slightly more red and slightly less green for a really beautiful white.
Perhaps around 600mW of red on the 637 end, 500 of 445 and 450 of 532. But again... just my opinion based upon my own projectors and experience.
Maybe i can share my experinece here since i am using about the same power range.
i'm using the great Laser Wave compact module the OEM pro S serie and i have great color balance but need to compensate in QS setup to reduce the green and blue
Here is what i have: joined with the read measured data i have
red ...637 170mW (measured 190mW) (single mode diode)
blue ..445 1W..... (measured 1.01W)
green 532 500mW.(measuerd 710mW)
I am reallly satisfied with and the orange look orange and yellow look yellow.
The white look cristal clear white snow white.. no greenish or bluish... just the right white =)
These compact module are really powerfull and easy to install !
Next will be to boost the red by adding another 170mW 637.... or maybe some knife edge with teh 120mW cheaper model.. will see...
Doc
.
Pangoline Quickshow FB3
H-RGB1800 with DT40 and Laserwave OEM pro S modules (r637nm 190mWg532nm 710mWb447nm 850mW)
Old set of G120 scanners and one Cambridge 6850
1.4W 445 blue pointer