Page 1 of 2 12 LastLast
Results 1 to 10 of 19

Thread: First Build - Overwhelmed!

  1. #1
    Join Date
    Feb 2013
    Location
    Toronto, Canada
    Posts
    33

    Default First Build - Overwhelmed!

    Hi All,

    this forum is an awesome resource for those interested in lasers to say the least! I was considering spending approx $400 on a green only ILDA scanner (Big Dipper M150G) however I am considering a custom build for better quality. I can spend up to $1000USD at this point therefore I should be able to end up with a decent final product. I spent most of the afternoon reading the forums and must admit that I am more confused than ever (too much information) due to the myriad of options available. One thing I do know is that I will start with a good base so I can add to it down the road in case I move to RGB. In regards to the scanner, I will go with the DT40Pro scanner for quality and longevity.

    I am not sure what to do for the remainder of the components. I will be using this device in medium sized halls and gyms and would like multiple bright, thick lines when displaying in a fan configuration (not sure of correct terminology). I would think that a 500mW to 1000mW would be required to achieve this. Can some of the experts recommend some of the components that I might try? I would prefer analog laser modules if possible for futures.

    I may even be daring enough to go with a green and blue setup if I can achieve decent quality for the $1K budget.

    Thank you!
    Last edited by jjspike; 02-17-2013 at 17:04.

  2. #2
    Join Date
    Dec 2008
    Location
    veenwouden
    Posts
    2,579

    Default

    with that budget i would advise to go DT30 since that is the best bang for your buck and its perfect for beamshows. The red will eat most of your budget unless you build that one yourself. For green 500mw is plenty and 1 watt of blue with a prismset is perfect to start with. The red could be a nice P73 corrective setup that would keep you within budget :-)


    Interested in 6-12W RGB projectors with low divergence? Contact me by PM!

  3. #3
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    The problem with your budget (any budget for that matter) is the unanticipated costs that are not related to the few obvious components in a laser projector. For example, the DAC or digital to analog converter that allows a computer to control a projector will cost maybe $100 up to $600 with bundled software. The power supply, wiring, connectors and switches etc will run at least $100. Then there is the robust (minimum 9mm thick) base plate and the enclosure; this will add another $100?

    Despite the way this might sound, I am not trying to discourage you. Rather, if you want the projector for the end use only and soon, then you might want to go CN and turn-key. But, if you think you want to take that first step, Bilbo, down a road where you can and might find you actually want to spend significantly more money as well as time, then welcome. And, keep reading. This is time very well spent. The jargon will thin out, certain themes will become apparent and you might begin to form a better idea of what you want to build.

  4. #4
    Join Date
    Feb 2013
    Location
    Toronto, Canada
    Posts
    33

    Default

    My past, and pretty much forgotten, electronics background does help however the laser specific terminology and optics are a bit over my head at this time. There is no doubt that something will be learned and this will be the payoff. I am fascinated by the internal workings of such devices and would much rather build something useful. My eldest teen is also a Physics wiz and this might be up his alley.

    I will read on fur sure!

    Thanks for your reply!



    Quote Originally Posted by planters View Post
    The problem with your budget (any budget for that matter) is the unanticipated costs that are not related to the few obvious components in a laser projector. For example, the DAC or digital to analog converter that allows a computer to control a projector will cost maybe $100 up to $600 with bundled software. The power supply, wiring, connectors and switches etc will run at least $100. Then there is the robust (minimum 9mm thick) base plate and the enclosure; this will add another $100?

    Despite the way this might sound, I am not trying to discourage you. Rather, if you want the projector for the end use only and soon, then you might want to go CN and turn-key. But, if you think you want to take that first step, Bilbo, down a road where you can and might find you actually want to spend significantly more money as well as time, then welcome. And, keep reading. This is time very well spent. The jargon will thin out, certain themes will become apparent and you might begin to form a better idea of what you want to build.

  5. #5
    Join Date
    Jan 2012
    Posts
    291

    Default

    Hi jjspike,

    First of all welcome to PL!
    Just make a simple list of parts your going to need to build a projector yourself.
    Here is a list which you could fill in with your own needs:

    - Projector case
    - Scanner set
    - ILDA/DMX PCB
    - Green module
    - Blue module
    - Red Module
    - Power supplies
    - DAC & software to control the laser
    - check-up by a authorized instance, so your sure the projector is safe to use in public.

    - Safety course, not relative to the projector itself but it's a must to know where your working with, you should do this before start building if you ask me!
    Lasers are very nice and most of us are addicted to them but also have to be handled with care, they could be dangerous!

    This is the basis stuff your gone need to build a projector.
    You can buy most parts or you can build some of these your own, like the laser modules (red/blue, the green needs some higher skills) and the projector case.
    Here on PL you can find allot of topics about building your own equipment, and when your stuck there are several people who will pleased to help you with the difficult parts.

    If your gone build your modules yourself then the parts your have to think about would be:
    - Module enclosure (f.i. metal shop or buy a enclosure and modify it to a laser module)
    - Diode mounts (you can find most parts in webshops like the ones from our members, like Dave from Lasershowparts or Rob from Stanwax lasers)
    - Laser diode driver (i could recommend the driver from Thomas alias Badpip, but there are more here on PL.
    - TEC cooling & controlling (when you want to keep the diodes on recommended temperature you have to cool them down, the diodes generate a amount of heat which could kill the diode if it's gets to hot.
    Some do use TEC's and some don't it depends on the passive cooling quality and amount of heat produced by the diode(s) of your build if you need them.
    - Optics, to collimate the laserlight from the diode you need a collimator lens (it depends which "diode" color you have on what kind of diode lens you need), there are more then enough topics with builds and do and don't on these lenses (Dave and Rob sell them, and some other members have there groupbuy topics).
    - Correction optics, sometimes your also gone need correction optics because the beam diffuses to fast, some uses cylindrical lenses and others uses prism pairs, again it depends on you build which you will need (Dave and Rob sell these or search the groupbuy topics).

    Of course you need some skills next to just understanding how it works, like soldering and the basics of electrical engineering and how optics work.
    Most of the newcomers think it's easy to build a projector there self, and i can understand it looks pretty easy until you start building!
    And if the budget isn't that wide you can't make big mistakes or do allot of testing on the parts (like optics and diodes, these will make your budget decrease very quick!).

    The last thing i can say is, when your gone build it yourself your not gone get a fully working RGB projector for the budget you have right now.
    If i may guess you will need at least twice the amount you have saved already, but you can build it step by step, like starting with green maybe a blue and then finish later with a red one.
    Like Planters said, there are several parts which you need and take a serious amount of your budget.
    Cables, connectors, PSU, costs to build the projector case for the metal shop and all that kind of stuff.

    If you still want to build it yourself after reading this then i wish you all the luck finishing your project and otherwise there are also some people on PL who build modules for selling which will make it a little easier to finish you first projector or they can sell you a complete projector which will fit your budget.

  6. #6
    Join Date
    Aug 2008
    Location
    UK
    Posts
    5,704

    Default

    Hey guys I think a few of you missed it but he only wants to go GREEN 1st then RGB later.

    He should be able to do that for not a mile away from his budget. So what he's looking for basically is an RGB case to fit out green only but possibly RGB later.

    Some people have found good deals on CNI Greens recently so I suggest he might want to look for a CNI green as I don't think Laserwave is doable in his budget and then an RGB case and DT30's or 40's.

    If there's no money for DAC or software then Spagehtti might be a good start or Pangolin Quickshow if he can afford to throw some money at it over and above his projector budget, as the latter will help him achieve what he wants very easily and simply.

  7. #7
    Join Date
    Feb 2013
    Location
    Toronto, Canada
    Posts
    33

    Default

    Fantastic summary astatic! You information is excellent and clarifies some of the things that I have been reading about. I plan building a platform that I can grow into therefore I will carefully plan before I jump in. I have not investigted the savings between building and buying laser modules so I think I will start with this as it will provide ground-floor knowledge. Based on some of the builds that I have seen, if all of my modules are identical in shape/size, my table layout will be more efficient and simpler to design/build. I still have much to learn and appreciate the advice of the experts!

    Cheers!

  8. #8
    Join Date
    Feb 2013
    Location
    Toronto, Canada
    Posts
    33

    Default

    Thanks for the reply White-Light. I will be starting-off simple with a green setup and adding-on from there. I believe this is the best way to avoid some of the costly mistakes that I have read about. Then again, this theory may be flawed. Anything can happen as even the most experienced sometimes make mistakes. I will be looking around to see if I can find an enclosure kit that will allow me to do what I would like to and then order components to build some laser modules. I will go the Pangolin route over-and-above my build as it will make things less complicated.

    Unfortunately, if you want to play, you've gotta pay! The real crux of the issue is that I have too many expensive hobbies and I have to draw the line somewhere. I will try to justify this by the fact that it will be a true learning experience for myself and the boys ;-)

    Cheers!




    Quote Originally Posted by White-Light View Post
    Hey guys I think a few of you missed it but he only wants to go GREEN 1st then RGB later.

    He should be able to do that for not a mile away from his budget. So what he's looking for basically is an RGB case to fit out green only but possibly RGB later.

    Some people have found good deals on CNI Greens recently so I suggest he might want to look for a CNI green as I don't think Laserwave is doable in his budget and then an RGB case and DT30's or 40's.

    If there's no money for DAC or software then Spagehtti might be a good start or Pangolin Quickshow if he can afford to throw some money at it over and above his projector budget, as the latter will help him achieve what he wants very easily and simply.

  9. #9
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    Unfortunately, if you want to play, you've gotta pay! The real crux of the issue is that I have too many expensive hobbies and I have to draw the line somewhere.
    On the Pangolin DAC front, set up a search for Pangolin FB3 on ebay. They come up periodically second hand, you'll pay around £300 (or whatever that is in dollars) and they hold their value, so you'll get your money back if you decide this isn't for you. The Quickshow software is available for download from the Pangolin website so don't be put off if it's out of date or missing - the media disk is largely irrelevant (and the one you might receive is likely to be out of date anyway!)

    Speak to Winni or Mimi at Goldenstarlasers for a case, they have a nice size RGB dual level case, (and a flightcase if needed) for a good price. Buffo on the forum got one recently and did a little write up, I can't quite remember where now, a search shold turn it up. they can also do you a deal on the DT30's or 40's to go in it (I would go for the DT30's personally, I have 5 RGB projectors, 2W up to 3.5W all with DT30's and they're fine for beam shows and reasonably straightforward graphics - I run all my work at 18kpps anyway!)
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  10. #10
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,835

    Default

    jjspike,

    there are cheaper and very capable alternatives to pangolin.

    this is about half the cost of the FB3/Quickshow:

    http://www.ebay.com/itm/LSX-RIYA-Las...item2ec09c100c

    and is very good software. it is more complicated (higher learning curve) than quickshow, but has more features. quickshow is easy and immediate. it's good for button mashing and beat matching during live performances, but this doesn't interest me very much as i prefer to program canned shows for later playback. lsx is capable of some really blow your mind effects and comes the closest i've ever seen to producing abstract console like effects in software.

    they're both capable products. it's really about what your needs and price range is.


    Quote Originally Posted by jjspike View Post
    Thanks for the reply White-Light. I will be starting-off simple with a green setup and adding-on from there. I believe this is the best way to avoid some of the costly mistakes that I have read about. Then again, this theory may be flawed. Anything can happen as even the most experienced sometimes make mistakes. I will be looking around to see if I can find an enclosure kit that will allow me to do what I would like to and then order components to build some laser modules. I will go the Pangolin route over-and-above my build as it will make things less complicated.

    Unfortunately, if you want to play, you've gotta pay! The real crux of the issue is that I have too many expensive hobbies and I have to draw the line somewhere. I will try to justify this by the fact that it will be a true learning experience for myself and the boys ;-)

    Cheers!
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •