Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 28

Thread: Dual red very dim. refocusing needed?

  1. #11
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,836

    Default

    just remember those diodes are super static sensitive.

    Quote Originally Posted by masterpj View Post
    Thats very awsome of you!
    Also I had not that much trouble getting both diodes out
    Attachment 37609
    I think I can pick up the diode tomorrow I have to finish up a bit of work.
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

  2. #12
    Join Date
    Jan 2012
    Posts
    291

    Default

    Great Pj, i'll be home, just give me a call when you come.

  3. #13
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    Grab a single mode 110mW mitsubishi diode. Awesome beam, cheaper than op next and 638nm. It could probably be over driven a bit too.
    If you're the smartest person in the room, then you're in the wrong room.

  4. #14
    Join Date
    Jan 2012
    Posts
    291

    Default

    @Absolom, the Opnext 120mw is cheaper then the Mitsubishi there $34,- vs $45,-
    You can easily overdrive them, 290mw without dropping power or changing into a led, i think a 150mw stable 638nm would be possible with these maybe 175mw like his bigger brother which you have to pay $129,- for.
    Problem is that Pj's diode mount is 5.6mm and the single modes where talking about are all 3.8mm.

  5. #15
    Join Date
    Jul 2010
    Location
    Netherlands
    Posts
    3,322

    Default

    Quote Originally Posted by swamidog View Post
    just remember those diodes are super static sensitive.
    Yep aware of that .
    I didn't touch the diodes and I have a special wrist band thats grounded and I discharge equipment before I touch it.
    Sadly it wasn't ESD that took these diodes out but likely some kind of voltage spike caused by the bad and unreliable connections present in the projector.

    Now I have re-wired the projector and made sure all solder contacts are nice and shiny (and firm).
    Off course I shrink tubed the connections too to make sure the connections are extra strong and properly isolated.

    Quote Originally Posted by astatic View Post
    Great Pj, i'll be home, just give me a call when you come.
    Will do!

  6. #16
    Join Date
    Jul 2010
    Location
    Netherlands
    Posts
    3,322

    Default

    Sorry I couldn't come yesterday
    Send u a text if I'm still able to come.

    Just putting the message here just incase u miss it.
    I will await a reply and then be on my way *if its still possible off course*

  7. #17
    Join Date
    Jul 2010
    Location
    Netherlands
    Posts
    3,322

    Default

    tumblr_mkl8i2wyuu1r95qbjo1_500.jpg
    it's alive! (Thanks to bart for the diode).

    I need a different lens though
    I'll check if I can replace it.
    Not sure which one I would need though.

  8. #18
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,836

    Default

    what diode did you put in there?

    Quote Originally Posted by masterpj View Post
    tumblr_mkl8i2wyuu1r95qbjo1_500.jpg
    it's alive!
    though I would need a different correction lens
    I'll check if I can replace it.
    Not sure which one I would need though.
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

  9. #19
    Join Date
    Jul 2010
    Location
    Netherlands
    Posts
    3,322

    Default

    Quote Originally Posted by swamidog View Post
    what diode did you put in there?
    300mw multimode 638 Mitsubishi

  10. #20
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,836

    Default

    ok. yeah. you will need corrective optics.

    Quote Originally Posted by masterpj View Post
    300mw multimode 638 Mitsubishi
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •