Is it a simple job to flip the x or y axis on my DT40's? My x- axis is the wrong way round and I have to tick the box in Quickshow to correct it. The feature in the LCD panel with the projector doesn't seem to work?
Is it a simple job to flip the x or y axis on my DT40's? My x- axis is the wrong way round and I have to tick the box in Quickshow to correct it. The feature in the LCD panel with the projector doesn't seem to work?
If your scanners are differential input, then just flip the input wires. Leave the ground where it is and exchange the inverting and non-inverting signal inputs.
James.
Creator of LaserBoy!
LaserBoy is free and runs in Windows, MacOS and Linux (including Raspberry Pi!).
Download LaserBoy!
YouTube Tutorials
Ask me about my LaserBoy Correction Amp Kit for sale!
All software has a learning curve usually proportional to its capabilities and unique features. Pointing with a mouse is in no way easier than tapping a key.
Or on each scanner amplifier there are a pair of jumpers in either = or || position. Take them off and reinstall them by 90˚.
- There is no such word as "can't" -
- 60% of the time it works every time -
You may find your X-axis is always the wrong way around for something out of the box!
If you're projecting graphics onto a wall and the graphics are correct with your scanners, the beams will almost certainly be mirrored from a standard QS or Beyond setup (remembering that your audience views beams from the front so whilst they may appear correct when viewed from behind the projector they are in fact mirrored from the front). If your projecting beams and have the scanners set to project these correctly, the graphics will be mirrored when projected onto a wall (as the graphics are then orientated for scrim projection).
The reason why its set up this way I guess is because most people project either graphics against the wall or beam shows (not both), in which case you set your scanners up for what you do, and for those people that tend to do beams + graphics, they are nearly always using a scrim as its only the real way to mix the two without having your audience turn around to face the back wall, and a scrim necessitates having the zones mirrored relative to each other as the graphics are then rear projection! So the software is set up to reflect how most people orientate their graphics and beams relative to each other.
Now if you like to project either graphics against a wall for one instance of use and then beams for another instance of use but never the two together in the same show and never against a scrim, then I would say the answer is to orientate your scanners to the beam zones correctly using the hardware settings and then flip the X axis in the projection zone geometric correction settings to correctly orientate the graphic zone for wall projection - it's usually easier here to orientate the scanners permanently towards beams and flip the graphics zone because there's only one graphics zone as standard but several beam zones, so orientating the beams zones correctly using the hardware and flipping the graphics zone, saves you having to flip multiple zones.
Dan has described above how to permanently orientate your scanner hardware to your favoured projection.
In any case, you can flip zones at any time by simply changing the orientation in the projection zone (geometric) settings (which persist after shutdown), or for a quick master flip of everything - selecting invert X in the main projector settings dialogue or if your projector has a flip X switch, throwing that.
Bear in mind a master flip of everything whether hardware or software flips everything so if the certain zones are wrongly orientated relative to each other for your particular usage, they will still be wrongly orientated to each other after flipping, its just a quick way of bringing the "wrong" zone into correct orientation for a particular purpose but only the use of Geometric Zone correction can permanently correct the relative orientation between zones if they're wrong for your common purposes.
Last edited by White-Light; 07-10-2013 at 02:45.
Excellent, have seen them now, cheers!
Thanks for that too, it makes sense I guess, I've been looking at scrim, where can you get some a decent price, it's expensive isn't it?
I have spoken again with Winni, the x/y flips as requested only work in auto mode from the lcd panel, not when using the ILDA plug!! How annoying...
You can use a pair of DPDT (double pole, double throw) switches in line with the signal wires to your scanners' differential inputs to be able to flip either axis the way you want them.
James.![]()
Creator of LaserBoy!
LaserBoy is free and runs in Windows, MacOS and Linux (including Raspberry Pi!).
Download LaserBoy!
YouTube Tutorials
Ask me about my LaserBoy Correction Amp Kit for sale!
All software has a learning curve usually proportional to its capabilities and unique features. Pointing with a mouse is in no way easier than tapping a key.
I have Scanner external beam show problems.
The scanner is not keep the positions the beam show on outside mirrors. About 20 - 30minutes, and the positions slipping some cm.
The Scanner is wrong or other problem?
Photos: https://www.photonlexicon.com/forums...hp?albumid=422
My edited show videos in youtube: https://www.youtube.com/playlist?lis...3JHLjLat29Z7Nk