Page 2 of 6 FirstFirst 123456 LastLast
Results 11 to 20 of 55

Thread: PT-40k(60k) Scanner Set

  1. #11
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    Quote Originally Posted by JD3 View Post
    I guess to circumvent this i could project the ilda pattern and full angle in the software, adjust the scan rate until it projects correctly(regardless of flicker), and set a max scan rate in beyond.
    Adam can probably help a bit better here but lowering the scan rate isn't exactly going to help. The scanners would need to be retuned for a lower scan rate. Basically, you should always tune your scanners to run at the speed and angle at which you intend to use them.
    If you're the smartest person in the room, then you're in the wrong room.

  2. #12
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    Quote Originally Posted by absolom7691 View Post
    ^^^^ What he said. I have heard of EMS-4000s (Eye Magic) being pushed at crazy wide scan angles.
    Just so i know im thinking the right thing.

    When i adjust size and position, in projector settings, in Beyond. If I stretch that box as wide as it goes, that is only making it as wide as the scanner was designed to do right?
    So what would be considered pushing it?

    Im not sure what scanset is in my CS series lasers. but i run them as wide as the software allows and assign scan rate to a fader on my midi.
    I "tune" them in the software with the ilda test pattern as large as the software will allow me to (in the size and postion section). as soon as the image starts to draw tails/stops flickering/circle gets too big, i back it off just a bit and set that as my max in beyond.
    This way during the show i can use the fader to make the image flicker really bad by bringing scan rate down to 6k on a complex set of beams to give a strobbing flicker effect. I can also do the opposite and smooth the beams out by adjusting it the other way to my max.

  3. #13
    Bradfo69's Avatar
    Bradfo69 is offline Pending BST Forum Purchases: $47,127,283.53
    Join Date
    Jul 2010
    Location
    Wilmington, DE
    Posts
    6,207

    Default

    Quote Originally Posted by JD3 View Post
    I dont charge enough for shows to afford those
    Neither do I. (But I have 'em anyway. LOL)

  4. #14
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    Those scanners (in my current lasers) will draw that ILDA30k pattern at about 12-13k (with flicker) when i have the size stretched all the way to 100% of what the software will allow x and y

  5. #15
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    Quote Originally Posted by Bradfo69 View Post
    Neither do I. (But I have 'em anyway. LOL)
    Excellent justification, if you ask me. Hell, I don't even do commercial shows and I have way more than I should!
    If you're the smartest person in the room, then you're in the wrong room.

  6. #16
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    Quote Originally Posted by Bradfo69 View Post
    Neither do I. (But I have 'em anyway. LOL)
    Haha! I guess i need a raise at work

  7. #17
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    It took me almost five years to acquire all the stuff I have now and I haven't even begun on my lumia projector yet. I am still amassing parts. Sometimes, as painful as it is, you have to save up.
    If you're the smartest person in the room, then you're in the wrong room.

  8. #18
    Bradfo69's Avatar
    Bradfo69 is offline Pending BST Forum Purchases: $47,127,283.53
    Join Date
    Jul 2010
    Location
    Wilmington, DE
    Posts
    6,207

    Default

    Quote Originally Posted by absolom7691 View Post
    Excellent justification, if you ask me. Hell, I don't even do commercial shows and I have way more than I should!
    I'm the poster child for way more than I should.

    Ok so, here's a question based on your statement:

    Basically, you should always tune your scanners to run at the speed and angle at which you intend to use them.

    Are you suggesting this on a per show basis? I don't claim to be a scanner or tuning authority. Yes, I've been hand held through the process a few times and have assisted others with their tuning but, it's just been simply a matter of setting the projector up, shining the ILDA 30k test pattern on the wall and tweaking the circle in the box to make sure it's round and touching the edges of the box. I know to do it accurately for a particular scan angle you need to have the projector a specific distance from the wall and the actual test image set to a certain size and we've done that with a tape measure. But, then I'll just use the projector for whatever. It might be set stupid wide for a beam show one night and then a week later be showing graphics on a wall. I don't do anything different with the tuning at that point.

    Edit... Oh, and since I didn't "go away", I should address the OP's answer. I have 4 sets of PT40's from Lihtspace and so far, I'm very pleased with them. I haven't really pushed them too hard yet because I don't want to have to buy another set of scanners to replace them but, thus far, they've been great.

  9. #19
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    Quote Originally Posted by Bradfo69 View Post
    I'm the poster child for way more than I should.

    Ok so, here's a question based on your statement:

    Basically, you should always tune your scanners to run at the speed and angle at which you intend to use them.

    Are you suggesting this on a per show basis? I don't claim to be a scanner or tuning authority. Yes, I've been hand held through the process a few times and have assisted others with their tuning but, it's just been simply a matter of setting the projector up, shining the ILDA 30k test pattern on the wall and tweaking the circle in the box to make sure it's round and touching the edges of the box. I know to do it accurately for a particular scan angle you need to have the projector a specific distance from the wall and the actual test image set to a certain size and we've done that with a tape measure. But, then I'll just use the projector for whatever. It might be set stupid wide for a beam show one night and then a week later be showing graphics on a wall. I don't do anything different with the tuning at that point.

    Edit... Oh, and since I didn't "go away", I should address the OP's answer. I have 4 sets of PT40's from Lihtspace and so far, I'm very pleased with them. I haven't really pushed them too hard yet because I don't want to have to buy another set of scanners to replace them but, thus far, they've been great.

    This is exactly what i was referring to. Every setup is different and none are permanent installs. IF the room permits i run as wide as an angle as possible and usualy rather narrow (i have also noticed better scanner performance, the smaller the scan area (regardless of how wide) the better the performance. these are just my observations)

    My friend speaks pretty highly of the PT scanners, but i really like getting objective and subjective views keeps me aware of potential problems.

  10. #20
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    Well, this is what I got from Adam when I was having trouble with my polyswitch on my PTs and this is how he explained it to me...... This is from a PM.

    Quote Originally Posted by buffo
    Quote Originally Posted by absolom7691
    Hey Adam, I just had a brief tuning question for you and was hoping you could shed some light on my problem. I have a pair of PT-40K chivos. I have gotten them tuned pretty decently at 30K @ 8°. In fact, the circle is larger than the square in both axis and the square has no over/undershoot.
    Oops! That's part of your problem then. Many people make this mistake: They assume that if it's good when the circle just touches the square, then it must be very good if the circle is bigger than the square. But this is not the case. What you have done is to overshoot the 30Kpps tuning point. You are probably tuned to something closer to 35K or more. (To check this, you can increase the scan speed while scanning at a small angle, like 4 degrees, and see what speed it takes to get the circle back inside the square.)

    What this means is that the servo gain is too high. That also means that the low and high frequency damping settings are also too high. The result is that the scanners are working much harder, drawing more current than they should be and getting a lot hotter in the process.
    When I increase the image size via software by 15%; the pattern shows fine for a second or two and then the circle slowly starts to deform and then the pattern goes nuts. The image breaks down into something unrecognizable and will not recover unless I stop scanning, set the size smaller again and then show the image. Is this a power limiting issue?
    Yup. Sounds like you're maxing out the current of the PSU, and when the pattern turns to hash, that's the poly-switch on the amp tripping. When you cycle the power off and back on, the poly-switch resets. Classic symptoms of someone who has tuned their scanners too fast. (Don't feel bad, it's easy to do, and the fix is also pretty easy.)
    So, I take that to mean that if you are not going to run your galvos at 40K but they are tuned for 40K, they are going to be working harder than they need to. This is why I prefeaced this with "Adam may be able to help"

    After this PM, I retuned my glavos and was able to hit 13.5° at 30K with no problems.
    If you're the smartest person in the room, then you're in the wrong room.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •