Results 1 to 10 of 10

Thread: Maximum amperage for P73

  1. #1
    Join Date
    Jan 2011
    Location
    Boston
    Posts
    255

    Default Maximum amperage for P73

    My new projector have four P73's cubed up. I'm currently driving them at 1 amp each. I have a massive heat sink below the baseplate, so they are remaining 22C even at that current. I'm still not color balanced, and would love a bit more 638 in the mix. Has anyone driven them higher with good results, or am I at the limit?
    Thanks

  2. #2
    Join Date
    Apr 2010
    Location
    Grand Rapids, Mi
    Posts
    2,538

    Default

    I drive them at 1.29a, but tec cool at 20c
    leading in trailing technology

  3. #3
    Join Date
    Jan 2011
    Location
    Boston
    Posts
    255

    Default

    Thanks. At 22C, I'll bring them up to 1.25A and see how it goes.

  4. #4
    Join Date
    Apr 2010
    Location
    Grand Rapids, Mi
    Posts
    2,538

    Default

    Just watch the power meter, if it starts declining due to heat, you'll have to back down the amps.
    leading in trailing technology

  5. #5
    Join Date
    Nov 2010
    Posts
    346

    Default

    820mA@16C. I'm a goof

  6. #6
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    Fearless,

    Do you know how about much power you are getting out of each diode? I agree with Polishedball that the best indicator of when to stop upping the power is when the output begins to curve away from linear. Because these are not too pricy you might consider driving one or a pair (however you are grouping them on the driver) harder than the others and if it tolerates this for some period then step each up by the differential and run them again for a while. This way you get more output without risking all 4 and with time you gain confidence with how hard to drive them. At RT I drive them @ 1.1A. At -25C I drive them at 1.5A. I have driven them at 2A @ -78C and one went LED @ 2.5A at LN2 temps. I am pretty sure that this last failure was due to facet damage as I inspected it postmortem. Therefore, as long as the output is below 2W and the metal components remain cool I think 1A to 1.5A is a reasonably safe range.

  7. #7
    Join Date
    Apr 2009
    Location
    Zürich-Bangkok-Dubai
    Posts
    275

    Default

    Planters, how much nm does the colour shift @ -25C? is it close step to deep orange/red in colour?

    Love your youtube channel btw
    Philipp Wetter

  8. #8
    Join Date
    Jan 2011
    Location
    Boston
    Posts
    255

    Default

    Hi Planters,
    I guess now is the time to invest in a laser power meter. I'm going to go with 1.25 for a while and see how the temps go. Right now the red red and blue are at 22C, even with constant use. I must admit that with the new green at 2 watts+ and the 2 M9 445's, this laser setup is waaayyy more powerful than my previous rig. Omar's scanners are working great, although they need a little tuning. As I've already tuned the DT40's, these should be no problem.
    Any more info on the NELEM? Is Krazer getting a space?

  9. #9
    Join Date
    Feb 2011
    Location
    New Hampshire
    Posts
    3,513

    Default

    JRG...,

    With approximately -45C from ambient at a constant driving current you will see about 8-10 nm shift. This is detectably more orange, but only in comparison with the diode's un-cooled beam. I don't think you will notice it in isolation. Also, the efficiency and the VISIBILITY each rise significantly. Expect about 25-30% higher output and (you have to check the visibility curves) maybe 10% increased visibility. It gets much brighter.

    Fearless,

    I understand he has the space, but I haven't heard yet any specifics. You might PM him to bump him a bit and get some specifics.

  10. #10
    Join Date
    Jan 2007
    Location
    Florida
    Posts
    4,382

    Default

    Quote Originally Posted by planters View Post
    At RT I drive them @ 1.1A.
    Wow this is good news. I have also been underdriving mine at 830mA lol
    Time to spin it up ..

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •