Results 1 to 5 of 5

Thread: Dualin' Blues - need some advice here

  1. #1
    Join Date
    Apr 2009
    Location
    North of Jackson Michigan USA
    Posts
    379

    Default Dualin' Blues - need some advice here

    Greetings, all;

    Here is my second attempt at building a dual 445nm laser. The first had alignment issues and ended up in a lumia projector - what I learned from that I applied here.

    This is part of a ~10W RGB projector I am building with CDBeam; he is building a 4W red, I'm doing the blue (4W, I hope), and I bought a 2W 532 from Planters. The resultant lasers will be fed to a set of DT-40s from Laser Show Parts.

    Parts:
    445 diodes, housings, G-2 lenses: DTR
    Diode Driver, 1/2 wave plate, PBS cube: Dave at LSP
    Lasorbs: Pangolin
    TECs: from a shoebox in Wayne Gillis's basement shop, discarded from a big time laser company
    TEC driver: PWM from a kit - http://www.bakatronics.com/shop/item.aspx?itemid=383
    Waveplate holder, M1 kinematic from Thorlabs (bought M1 used on eBay).
    Various aluminum pieces bought at Alro in Ann Arbor
    Anamorphic prisms: CDBeam provided these, left over from a lumia project

    I machined all the aluminum parts in my shop, crudely (see diode holder for less-than perfect finish).
    All these pix are on my website at: http://mondodyne.com/1dualBlue/

    Here is my workbench as I am gearing up:
    blue build Bench.jpg

    This is my first attempt at TECing things, so I machined diode holders out of one piece of aluminum for best thermal transfer:
    blue build 1.jpg

    This shows the mount, sitting in front of the angle iron that supports Dave's driver.
    Note second TEC awaiting its destiny under the second diode. Nylon screws hold the mounts down to prevent thermal feedback. The holder has a front and side lip to provide maximal coverage of the liberally-greased 1" square TEC.

    Here is a top view of the unit:
    blue build 2.jpg

    The pot in the middle of the right hand side controls the PWM mojo going to the TECs.
    This is an $8 controller originally intended as a motor speed control. I use these extensively in my lumia projectors. I heat-sinked the output transistor of this just for good luck. If time and $$ permit, we may add a thermostat controller for this; for the moment I am just cranking it up to what seems a good level to get max out of the diodes.

    Another shot showing CDBeam's prisms at the business end.
    blue build 3.jpg

    And head-on for full appreciation of the M1 holding the PBS:
    blue build 4.jpg

    Beam shots, I hear you ask?
    blue build 5.jpg

    As part of the alignment process, I bounced the beam back and forth across my office/lab:
    blue build6.jpg
    blue build7.jpg

    Ending up, after a ~55ft throw, with a beam profile that looks like this:
    blue build8.jpg

    And that is where I'm stumped: I would like a square output, but am getting a "spot" of around 55mm X 5mm, after an approximate 55ft. throw. I am using Zoof's template for the prism alignment, and have tried tweezing that a bit, to no avail.

    What am I doing wrong?

    Comments and criticisms welcomed.
    Thanks much.

    Lux Plus Esto...Mike
    Runs with Lasers

  2. #2
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,835

    Default

    i would ditch the waveplate and physically rotate on of the diodes so you get a symmetrical spot shaped like this "+".

    better yet is to correct each beam before combining it with the pbs cube:

    dual-445-render.jpg

    complicated-445.jpg

    and from 40 feet:

    dual-445-ap-08.jpg



    Quote Originally Posted by clickamouse View Post
    Greetings, all;

    Here is my second attempt at building a dual 445nm laser. The first had alignment issues and ended up in a lumia projector - what I learned from that I applied here.

    This is part of a ~10W RGB projector I am building with CDBeam; he is building a 4W red, I'm doing the blue (4W, I hope), and I bought a 2W 532 from Planters. The resultant lasers will be fed to a set of DT-40s from Laser Show Parts.

    Parts:
    445 diodes, housings, G-2 lenses: DTR
    Diode Driver, 1/2 wave plate, PBS cube: Dave at LSP
    Lasorbs: Pangolin
    TECs: from a shoebox in Wayne Gillis's basement shop, discarded from a big time laser company
    TEC driver: PWM from a kit - http://www.bakatronics.com/shop/item.aspx?itemid=383
    Waveplate holder, M1 kinematic from Thorlabs (bought M1 used on eBay).
    Various aluminum pieces bought at Alro in Ann Arbor
    Anamorphic prisms: CDBeam provided these, left over from a lumia project

    I machined all the aluminum parts in my shop, crudely (see diode holder for less-than perfect finish).
    All these pix are on my website at: http://mondodyne.com/1dualBlue/

    Here is my workbench as I am gearing up:
    blue build Bench.jpg

    This is my first attempt at TECing things, so I machined diode holders out of one piece of aluminum for best thermal transfer:
    blue build 1.jpg

    This shows the mount, sitting in front of the angle iron that supports Dave's driver.
    Note second TEC awaiting its destiny under the second diode. Nylon screws hold the mounts down to prevent thermal feedback. The holder has a front and side lip to provide maximal coverage of the liberally-greased 1" square TEC.

    Here is a top view of the unit:
    blue build 2.jpg

    The pot in the middle of the right hand side controls the PWM mojo going to the TECs.
    This is an $8 controller originally intended as a motor speed control. I use these extensively in my lumia projectors. I heat-sinked the output transistor of this just for good luck. If time and $$ permit, we may add a thermostat controller for this; for the moment I am just cranking it up to what seems a good level to get max out of the diodes.

    Another shot showing CDBeam's prisms at the business end.
    blue build 3.jpg

    And head-on for full appreciation of the M1 holding the PBS:
    blue build 4.jpg

    Beam shots, I hear you ask?
    blue build 5.jpg

    As part of the alignment process, I bounced the beam back and forth across my office/lab:
    blue build6.jpg
    blue build7.jpg

    Ending up, after a ~55ft throw, with a beam profile that looks like this:
    blue build8.jpg

    And that is where I'm stumped: I would like a square output, but am getting a "spot" of around 55mm X 5mm, after an approximate 55ft. throw. I am using Zoof's template for the prism alignment, and have tried tweezing that a bit, to no avail.

    What am I doing wrong?

    Comments and criticisms welcomed.
    Thanks much.

    Lux Plus Esto...Mike
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

  3. #3
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,835

    Default

    that looks much better.

    Quote Originally Posted by clickamouse View Post
    Ah, I see.
    I like this design better; much smaller. Here is my first take on it:

    Attachment 41869

    Thanks much.

    …Mike
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

  4. #4
    Join Date
    Apr 2009
    Location
    North of Jackson Michigan USA
    Posts
    379

    Default

    Here is the attachment in question; couldn't remove the PDF without wiping the message.
    Blues2.jpg

    Thanks much.

    …Mike
    Runs with Lasers

  5. #5
    Join Date
    Apr 2009
    Location
    North of Jackson Michigan USA
    Posts
    379

    Default

    …so all I need to do is build an integrated 2-banger mount (and a new plate so I get fresh holes), add a steering mirror, and then I can re-use all the other components.

    I'm on it.

    …Mike
    Runs with Lasers

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •