Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Build nearing completion (sans case)

  1. #1
    Join Date
    Jul 2014
    Location
    With the Koalas
    Posts
    50

    Cool Build nearing completion (sans case)

    Hey folks,

    So it's been a while coming, but my build was powered up today for the first time, but it has an issue.
    FullSizeRender.jpg

    I'm not sure if this is a scanner tuning issue or a ground issue, or something else, so was hoping someone who knows will chime in. I projected the 12k Ilda pattern and this was the result:
    IMG_4209.JPG
    (the upload has rotated the image, my thumb is the top).

    I've been reading about grounding and noticed some commentary about not connecting the AC gnd and pin 25 to the same point, which I have done (all to the star connection), but others saying this has not been an issue.
    Both scanners are moving which I guess is shown by the smallish loop in the centre, so wondering if the tuning is off (they're meant to have been tuned pre shipping)

    Needing some input from those in the know.

  2. #2
    Join Date
    Sep 2006
    Location
    Netherlands
    Posts
    1,438

    Default

    Somehow the x and y channels have become linked.
    Look for a short between pin 1 & 2 or 14 & 15, maybe in the ildacable maybe in your own wiring.

    Are you *very* sure that the two layers of you optical deck are the same material ?
    Otherwise you may experience bimetalic warping.

    I see you use the connexelectronic smps, smps300RE ?
    Where did you get the scannermax / amp combo ?

  3. #3
    Join Date
    Jul 2014
    Location
    With the Koalas
    Posts
    50

    Default

    The amp is kvant version. I waited for the machmini for so long but got tired of sitting on the project. Wiring to the amp is in the form of a supplied ribbon strip peeled down to individual wires and then connected to a breakout. Tested for continuity between the pins mentioned on both the breakout board and the cable - both seem ok (ie no beeps).

    Power is indeed the smps300re. I've made a little rectifier circuit which is fed off the +/-12 aux of the board and regulated to 8V, supplying LSP drivers. I wasnt really sure it would be ok as I didn't have a manual to know what the aux out could do so I just built it to see, then I found a manual and saw the spec'd output as 500mA max. This works fine for me as I'm running at around 450ish (DTR bundle).

    As for the two layers, I'm not sure if you mean just the plate the diodes mount is sitting on? The image might be interpreted as a two layer material but that's just my dodgy metal work being picked up in the lens. ie I cut the piece from a plate and then filed a bevel and sanded it to a satisfactory finish for my purposes. (Unless you mean the plate and the heatsink?)

  4. #4
    Join Date
    Aug 2010
    Location
    London or Spain depending on the weather
    Posts
    1,390

    Default


    Quote Originally Posted by skot View Post
    ......Both scanners are moving which I guess is shown by the smallish loop in the centre, ...
    The fact that line is diagonal is what shows that both scanners are working, what is strange is that they are moving simultaneously almost all the time !

    thinking2.gifIf you are using differential signals...check that you are not using +x with -Y on one channel and +y with -x on the other.
    Also if your "little rectifier circuit which is fed off the +/-12 aux of the board and regulated to 8V, supplying LSP drivers"
    is connected with one side at zero (with respect to the controller input make sure it is also zero with respect to the scanner boards (when controller is NOT connected)!

    Cheers
    Last edited by catalanjo; 02-21-2016 at 10:09.

  5. #5
    Join Date
    Sep 2006
    Location
    Netherlands
    Posts
    1,438

    Default

    the aux channel is 250mA nominal 500mA peak.
    If you use a lineair regulator such as the lm317 that would be tight.
    A better solution would be to use a dc-dc converter based on the lm2596 which will give nominal 700 mA @ 8V.

    That said, it is very unlikely that the way you power your diodes is connected to the diagonal line issue.

    I can not find documentation on the kvant amp, did it come with documentation how to hook it up ?

    I always thought that gttech was owned by medialas, but now it is owned by kvant ? And the kvant treiber looks very similar to 2 medialas microamps glued together ??

  6. #6
    Join Date
    Aug 2010
    Location
    London or Spain depending on the weather
    Posts
    1,390

    Default



    @ "That said, it is very unlikely that the way you power your diodes is connected to the diagonal line issue."

    Not necessarily correct ...... since in the controller (what ever that is) the zero colour modulation reference is likely to be connected to the central zero volt PSU for the scanner amp and will also be connected (probably) to the zero reference of the scanner signal (screening) (unless the colour controls are balanced lines (unlikely).
    If the zero volt line from the PSU is not the same as the zero after the voltage reg circuit for the diode supply (eg derived from the plus and minus rails rather than the plus rail and zero ) it would mean that the regulated diode supply is using the negative scanner supply rail as its zero volts reference.
    If these are then connected together Either in the controller OR in a single earthing point in the projector, the negative side of the scanner supply would get very upset, ... causing the scanners to do strange things in unison, one with the other.

    Suggestion, ..... disconnect earthing point from all zero lines and disconnect controller, then check that there is no voltage between zero lines of scanner supply and voltage reg. PSU of diode drivers. If scanner PSU has no clear zero volt line then measure diode supply zero to scanner PSU negative and make sure you have full negative voltage there.
    If you don't have full voltage there, then use different source for the diode supply.

    Just my 2cents
    Cheers

    PS. If what you describe as the "+/-12 aux" is a real isolated AC supply voltage floating around zero, everything I have said above is a load of horsesh*t!
    Last edited by catalanjo; 02-21-2016 at 13:13. Reason: commas etc.

  7. #7
    Join Date
    Jul 2014
    Location
    With the Koalas
    Posts
    50

    Default

    Bart, no documentation supplied. I asked and was provided with the pinout details of the ribbon connector only(being both power input and scanner outputs connect on this cable).

    I'm not at all familiar with the medialas amps, but you're possibly somewhat correct. The input connector has 2 pins for +24 and 2pins for -24. I thought that was kinda weird as a design, but it makes sense with your statement.

    Looking back at the power supply docs I see that nominal 250 is mentioned in the table. I didnt read that far through the doc lol. I just saw the dot points where it says 500mA. I'd already built the supply by that stage so thought I'd give it a go. I can easily change it out. Thx for pointing that out.

    Catalanjo, I'll mull over that and go through my wiring. 8am Monday here, and I've got some things to do so I'll have to come back to it. Thx for the input.

  8. #8
    Join Date
    Sep 2006
    Location
    Netherlands
    Posts
    1,438

    Default

    The aux voltage is actually floating on my smps300re, so it should be on yours.

    Make absolutely sure you don't have the scanner feedback pins connected to anything. (which can lead to all kinds of voodoo sh*t)

    Grouping pins/leads for power supply is common practice to lower the impedance and raise current capability.

  9. #9
    Join Date
    Jul 2014
    Location
    With the Koalas
    Posts
    50

    Default

    Spent some time last night trying to work through this and decided to pull it apart and rewire it. Opened up my documents and laid out my notes and noticed that in my notes I'd transcribed the supplied ribbon pin out incorrectly. Instead of writing X+,X- then Y, I'd interchanged them to X+,Y+ & X-,Y-

    Switched them around and was able to get a projection. Simple case of user stupidity haha.

    Next step is going to be alignment and colour matching. I've got a rough alignment already using stanwax guide, with the final step to complete via the test patterns. At the moment it is very red heavy with not much green. But last night I just wanted to get some beams so I left this for another time.

    What's the best way to tune colour? I played with the software a little but wasn't very linear, so I'm thinking the driver current, but from when I set that up it was not very linear either so I am not sure what is the best option.

    I also need to look into the tuning process to see how to improve the projection of the ILDA test pattern as it did not seem to be very accurate ie the circle was not round. But that's for later.

    Really appreciate the input guys.

  10. #10
    Join Date
    Aug 2010
    Location
    London or Spain depending on the weather
    Posts
    1,390

    Default

    Quote Originally Posted by catalanjo View Post


    thinking2.gifIf you are using differential signals...check that you are not using +x with -Y on one channel and +y with -x on the other......Cheers
    @ -bart- "The aux voltage is actually floating on my smps300re, so it should be on yours."
    In which case " PS. If what you describe as the "+/-12 aux" is a real isolated AC supply voltage floating around zero, everything I have said above is a load of horsesh*t!

    QED.
    Cheers

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •