Page 1 of 3 123 LastLast
Results 1 to 10 of 30

Thread: Colour Switcher/Fader For Spiro Project

  1. #1
    Join Date
    Dec 2007
    Location
    England, Hertfordshire
    Posts
    333

    Default Colour Switcher/Fader For Spiro Project

    I recently bought 3 5cm fans and a 3 way RPM controller for it and I am wanting to make another simple spirograph, but this time I want to complicate things slightly but keep the small, maybe pocket, size.

    I want to build a simple controller that will fade/randomly change the colour of the laser. I will fit red, green and blue ray inside the enclosure and align them similar to a projector so that the colours can be combined.

    Is such a driver or anything avaliable out there? I don't need to manually controll it or even be able to program it, in fact even colours fading into each other slowly would do as I am only after the patterns it makes and not the beam effect.

    Would I just be able to use something simple like a flexdrive on each laser and having them all wired into one circuit to power them each and do its thing? I would like it all to fit inside a small plastic enclosure and be battery powered as well which does make things more complex.
    DL - Viper 75mW - Green (532nm)
    DL - 50mW Module - Green (532nm)
    DIY - 50mW - 12k Scanner - Green (532nm)

  2. #2
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Cool

    Quote Originally Posted by lamborgini8 View Post
    Would I just be able to use something simple like a flexdrive on each laser and having them all wired into one circuit to power them each and do its thing?
    That would be the easiest way, IMO. You'd want a set of 3 ramp generators feeding each of the three modulation inputs. Ramp up to +5 volts, hold, then ramp down and hold. Repeat. Maybe use a 555 timer to stagger the startup timing so you start with black, go up to full red, then fade to yellow, then full green, then fade to cyan, then full blue, then fade to magenta, and back to full red. From that point it will cycle through the 6 colors with no black. Of course, you won't get white that way...

    Adam

  3. #3
    Join Date
    Dec 2007
    Location
    England, Hertfordshire
    Posts
    333

    Default

    Quote Originally Posted by buffo View Post
    That would be the easiest way, IMO. You'd want a set of 3 ramp generators feeding each of the three modulation inputs. Ramp up to +5 volts, hold, then ramp down and hold. Repeat. Maybe use a 555 timer to stagger the startup timing so you start with black, go up to full red, then fade to yellow, then full green, then fade to cyan, then full blue, then fade to magenta, and back to full red. From that point it will cycle through the 6 colors with no black. Of course, you won't get white that way...

    Adam
    Hmm right, seams pretty simple. I would be able to have each colour either on or off and combining them that way instead of fading them which would be even easier. That way I will get all 6 colours plus the extra 'white'.

    I will be powering the motors and RPM controller seperatly from a 12V battery so how much power would I need to run three diodes and a 555 timer? Red and blue ray diodes run from 3V I think and the blue ray needs 5V but what about the 555 timer? Thats already 11V, with any luck it will run on another 1V so I can just have two 12V batteries inside.
    DL - Viper 75mW - Green (532nm)
    DL - 50mW Module - Green (532nm)
    DIY - 50mW - 12k Scanner - Green (532nm)

  4. #4
    Join Date
    Jul 2008
    Location
    Maryland
    Posts
    1,691

    Default

    well as long a s the voltage drop over the entire circuit is less than the total voltage your ok i think..

    but the question is how much power do yo realy have in mA.

    each diode will draw whatever its driver is set to, those drivers can be wired in parallel so there is no voltage drop.

    a 9v 2A power supply would work best i think.
    Quis custodiet ipsos custodies?
    Solid State Builders Group

  5. #5
    Join Date
    Dec 2007
    Location
    England, Hertfordshire
    Posts
    333

    Default

    Quote Originally Posted by keeperx View Post
    well as long a s the voltage drop over the entire circuit is less than the total voltage your ok i think..

    but the question is how much power do yo realy have in mA.

    each diode will draw whatever its driver is set to, those drivers can be wired in parallel so there is no voltage drop.

    a 9v 2A power supply would work best i think.
    True, all lasers will be wired in paralell and I am not looking for anything really high powered. I will get a 30mW green module, use one of my many red diodes and set that to 60mW and the blue ray at about 100mW.

    The whole thing has to stay small and powered by batteries. My aim is to have totally portable RGV spiro that is small enough to fit in 1 hand.
    DL - Viper 75mW - Green (532nm)
    DL - 50mW Module - Green (532nm)
    DIY - 50mW - 12k Scanner - Green (532nm)

  6. #6
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Cool

    If you're planning on having a 12 volt battery in there you can run everything off that. The 555 timer needs a minimum of 5 volts, but can take up to 15 volts. So 12 volts is fine.

    Adam

  7. #7
    Join Date
    Dec 2007
    Location
    England, Hertfordshire
    Posts
    333

    Default

    Quote Originally Posted by buffo View Post
    If you're planning on having a 12 volt battery in there you can run everything off that. The 555 timer needs a minimum of 5 volts, but can take up to 15 volts. So 12 volts is fine.

    Adam
    In theory I should be able to run all three motors, the RPM controller, three lasers and the 555 timer from one 12V battery if I wire the whole thing in paralell? Only downside I can think of is battery life.
    DL - Viper 75mW - Green (532nm)
    DL - 50mW Module - Green (532nm)
    DIY - 50mW - 12k Scanner - Green (532nm)

  8. #8
    Join Date
    Jan 2006
    Location
    Charleston, SC
    Posts
    2,147,489,632

    Cool

    Yeah, that's the way I'd do it. Pick some beefy cells and you should be fine.

    If you want to get fancy, you could build a custom battery pack that delivers 12 volts, 6 volts, and 3 volts... That way you can run the red and green drivers off 3 volts and the blu-ray driver off 6 volts. Not sure that it will buy you much improvement though.

    What sort of housing are you going to use?

    Adam

  9. #9
    Join Date
    Dec 2007
    Location
    England, Hertfordshire
    Posts
    333

    Default

    Quote Originally Posted by buffo View Post
    Yeah, that's the way I'd do it. Pick some beefy cells and you should be fine.

    If you want to get fancy, you could build a custom battery pack that delivers 12 volts, 6 volts, and 3 volts... That way you can run the red and green drivers off 3 volts and the blu-ray driver off 6 volts. Not sure that it will buy you much improvement though.

    What sort of housing are you going to use?

    Adam
    I think I am going to need a schematic drawing somewhere along the line...

    The lasers drivers will, or should, only take what they need to drive the laser so that shouldnt be a problem as such. Where this is getting complicated is where in the circuit will the lasers and drivers go if they are all connected up to the 555 timer?

    The enclosure is just going to be a cheapy small plastic one from Maplin, something like this:
    http://www.maplin.co.uk/Module.aspx?ModuleNo=1689 (note I havent measured up yet so it might not fit into that but thats the kind of thing I am after)
    The only powerful laser will be the blue ray so heat sinking them shouldnt be ok.

    I am attempting to keep the build as simple as possible. Yet from what I know, it will be the only RGV spiro around.
    DL - Viper 75mW - Green (532nm)
    DL - 50mW Module - Green (532nm)
    DIY - 50mW - 12k Scanner - Green (532nm)

  10. #10
    Join Date
    Dec 2008
    Location
    Vezon, Belgium
    Posts
    1,017

    Default

    just wire up a binary counter out of a 4017, and control from either a pushbutton or a 555, and you'll have a nice project!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •