Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 21

Thread: FAP800 Threashold ?

  1. #11
    Join Date
    Aug 2005
    Location
    Silicon Valley
    Posts
    442

    Default

    Threshold for the 12W FAP is likely 6-8A with a max current around 20A. Threshold for the 25W FAP is going to be close to 10A with a max current around 35-40A.

    Quote Originally Posted by Hemlock Mike View Post
    This seller has contacted me and is sending a "replacement" 25 Watt module. I hope it works. I only ordered the 12 watt unit but a 25 is OK with me......

    Mike

  2. #12
    Join Date
    Mar 2007
    Location
    North Iowa
    Posts
    249

    Default

    Steve -- My supplies are both voltage and current regulated. I also put a small dummy load across them to prevent open circuit spikes. My power supplies are always feeding a small amount of current to this load to maintain regulation.

    JT --- Thanks for the data. That is a help to me.

    Mike

  3. #13
    Join Date
    Jun 2007
    Location
    Lake Geneva, WI.
    Posts
    2,704

    Default

    That's the way I do it...

  4. #14
    Join Date
    Dec 2007
    Location
    Stockholm, Sweden
    Posts
    556

    Default

    When using FAP-modules in for example a laser engraver what kind of lens do you use? Is it easy to get hold of a piece of fiber and a suitable lens or is it going to be hard to find special items?

  5. #15
    Join Date
    Sep 2009
    Location
    san diego, ca
    Posts
    37

    Default

    From my experience, the FAP modules would not make for good engraving lasers. They are mulimode, 800 micron, and cannot be focused to a small spot suitable for engraving. At best, you could collimate/focus the beam from some optics in the verdi or avia heads. But these are uncommon to find. Before hooking up a fiber, you must inspect the diode tip and fiber tip for any particles or burns. 90% of those diodes and fibers sold as-is on ebay have micrscopic burns and will fail after short use.

  6. #16
    Join Date
    Jan 2007
    Location
    Cupertino, California
    Posts
    2,130

    Default

    There is a reason Coherent scraps these.
    CLICKY!!!

    Admin: In the immortal words of Captain Planet: YOU HAVE THE POWER
    Admin: (To quit being a bitch)

  7. #17
    Join Date
    Mar 2007
    Location
    North Iowa
    Posts
    249

    Default

    Ben --
    I noticed that when I received the first one that a heavy terminal was bent a bit. Today, I shook it and heard something loose inside. I think this one was dropped. I hope the new one is better.

    Mike

  8. #18
    Join Date
    Dec 2007
    Location
    Stockholm, Sweden
    Posts
    556

    Default

    Quote Originally Posted by greanbeam View Post
    From my experience, the FAP modules would not make for good engraving lasers. They are mulimode, 800 micron, and cannot be focused to a small spot suitable for engraving. At best, you could collimate/focus the beam from some optics in the verdi or avia heads. But these are uncommon to find. Before hooking up a fiber, you must inspect the diode tip and fiber tip for any particles or burns. 90% of those diodes and fibers sold as-is on ebay have micrscopic burns and will fail after short use.
    Ok, thanks for the information!
    It is hard to find a cheap 808 - 1064nm laser in a small package for engraving! It is not my aim to build a high accuracy industrial system but rather find something to try out and learn from on my soon to be finished cnc-router.
    I have a Synrad 14W 10,6um CO2 with good optics but I would like another wavelenght to try on some metal since the Synrad is mostly good on organic materials and glass/porceline etc.

  9. #19
    Join Date
    Mar 2007
    Location
    North Iowa
    Posts
    249

    Default

    I received my replacement module today Fedx. I was able to power it up to ~6.5 Amps and I read 0.98 watts output -- just above threshold.
    This is a 25 watt module and so far so good. It is a FAP800-25W-806 module. Will warmer or colder make it closer to 808 nM?

    Mike

  10. #20
    Join Date
    Sep 2009
    Location
    san diego, ca
    Posts
    37

    Default

    Being scrap units, 95% are unusable for 808nm. The bonding begins to warp on the bar, causing any cooling from the bottom to be lass effective. Also if one or 2 emmiters are damaged, the laser is working much harder to produce full power. The emmiters that do work have to work harder, causing more heat and needing more cooling. You may achieve 808nm at a reasonable temperature by running the diode at much lower power, like 10-15 watts. Check the diode tip under a micrscope, there could be burns. Anyway, these are good for experimenting, but dont expect any reliability or lifetime out of it.
    Last edited by greanbeam; 11-24-2009 at 21:34.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •