Hey Jonathan -
All due-respect to the proponents of the DF-50 (I'd agree, too, but in this-case...) personally, I'd go with a small fogger, and Martin / JEMs "iFog" - attached is the MSDS and they can clearly read from the manuf. what it is, and that it will be pretty 'inocuous' for this type of setting...
Yeah, we could continue the back and forth about 'mineral oil vs glycol', etc, but the reason for my 'suggestion' is that although a hazer is really the best way to get a nice 'ambient atmosphere' for visibility, in this-case, between their air-handlers, and their 'err on the side of extreme caution' policy, you'll likely never get to the 'levels' you really need in the room to make a 'difference'...
A small-fogger, close to your set-up, with a small, quiet fan (but strong enough to move air, well; ie; those small 5-6 blade 'turbo-fans' work well..) will allow you to put-out small, 'controlled puffs', right in front of the most 'important place' (where the Client is likely-looking - your projector.. at least for the beams, etc,) and thus, will 'see' the beams / aerials, etc - to them, they should-feel 'satisfied', cause they'll 'see' some of the 'desired-effect', while you stay in 'full-control', and no-where-near painting / furnishings-damaging or detector-tripping levels... (unless you're right-under one - be careful to take note of placement)![]()
..and if they give you any 'hooey' about 'not seeing beams, everywhere', you diplomatically 'ask them to choose': do they want to 'protect their environment, at all-costs'? (including beams, etc) OR, do they want a 'rock-concert'?...you can always 'put-out more', with the fogger-approach, but you're far-less likely to trip their 'sensitivities' - or their detectors - then with a hazer..
Side-note on detectors: If they're the 'heat-detecting' type, you're golden: the most-'forgiving'; if they're particle-detection style (ion-emitter/detector type) those are pretty-forgiving, but again, do-be careful of 'location' - best not to set-up right under one, but if there's no choice, keep the air moving and fog-puffs small; photo-cell detectors are notoriously much more sensitive - but, even-then, if you keep an eye on 'levels' / use small-puffs, you should be fine...
And this is where the 'iFog' excels - very 'dense' and 'white' so even a small amount will give nice results.. small 'puffs', regularly-spaced, good air flow, in the direction of your beams / aerials, and eminating-from right under / close-to your set-up, should give you nice, 'safe' results...I've done quite a few 'gigs' in some pretty-fussy museums / ballrooms, over the years, and this approach - in those circumstances - has never let us down...
DSLI_NASA_YurNt_2..jpg
Here's a nice auction for a Magnum Pro 2000 with a gal of iFog - http://cgi.ebay.com/ws/eBayISAPI.dll...m=170457405580 - if you don't wanna 'jump that high', here's someone selling 'just the juice' - http://cgi.ebay.com/ws/eBayISAPI.dll...m=120456003921 - (and, ps - I am not 'associated' with either of these sellers, no, I make no 'endorsements' / warranties, etc- just a 'friendly fyi'...) - and these have control over 'output' as well as timing, so you can dial it back to put out a near-constant / frequent 'trickle' vs an obnoxious 'puff'...
Yeah, these are not the 'top of the top-shelf' foggers, etc but I certainly think 'good enough', for this level of gig...it's not like this is a KISS concert, ok?And you don't have-to use this iFog with ONLY a Martin / JEM - any fogger that specs 'water-based' fluid (Chauvet, Antari or whatever they're called, etc) should be fine... so, if you find one of those-units 'local', you should be fine using the iFog...
Hope this helps...
peace..
j
Last edited by dsli_jon; 03-26-2010 at 13:54. Reason: sp
....and armed only with his trusty 21 Zorgawatt KTiOPO4...
I have to Agree that a DF50 would be a BAD BAD IDEA when out touring im running into more and more venues that wont allow DF50s as they are not water based and they DUE in any amount of use leave a residue esp in the area around the hazer. i would use a small water baised fogger or a water baised hazer such as Lematre or a martin Zr24/7 or a uniuque hazer. Any fog effect oil or water baise still has potental to leave a residue but out of the 2 the water baised fluid would be the "Safest" for your venue. i would use the fog as little as u could. you can also contact the diffrent companies and get a material hazards sheet on the fluid wich is always a great idea to have on hand anyways to show clients / venues etc... that your fluids are health safe and what they are composed of
To Chad:
I won't set off the fire alarm because fortunately for me, the building has not had them installed. It connects to the newer campus buildings that DO have them, but the connecting door is usually shut, meaning the fog or haze wont make it to a detection device.
To Steve: Because of where I have to set up in the room (there are limited places because of numerous reflective surfaces I have to avoid), I wont be very close to an intake. However the heating/cooling there is so weak, that even if I was close, it probably wouldn't make much difference (I will probably have to use a small fan). As for the size of the room, It's floor dimensions are very close to those of the SELEM auditorium. The ceiling is 2 stories high around the border and then dips in in the center of the room where the domed ceiling is, it's about 2 1/2 or 3 stories high. This is what I will be projecting on ( It used to have a massive hand painted mural on it, but the morons that got the mansion b4 my school turned it into storage temporarily and painted over it with white paint).
I will have to find out who the maintenance guy is.
To Paul:
What they want me to do is let the guests eat quietly whilst I flash "Merry Christmas Happy New Year", etc on the domed ceiling. When they finish eating, the lights will go out (un-announced to make it more dramatic) and I will begin doing beam effects followed by excerpts from one of my ADAT Christmas Shows that will be digitized by Christmas so that I can manipulate it a little. BTW, I will be overtly hazing the air 5-10 minutes before the real "show." This way the guests don't see any beams until the show starts (it should help with the 'shock' factor
). The last thing you should know is this will be a primarily Baby boomer audience (older folks), so I need to keep it 'toned' down but still interesting so I show them something new and exciting without giving them a heart attack
.
To laserist:
I don't know what a hepa filter is, but I can guess. I can also guess that they most likely don't have them. The museum is primarily original very little has been remodeled or touched since it's original conception. I will ask nonetheless.
To dsli_jon:
Thanks for the response, the small fogger sounds like a great idea to me. The only problem I see is that my goal is to saturate the air without the guests noticing. Fog is pretty noticeable while haze is much harder see if your not looking for it. Again, the smoke detectors are not existent and therefore not a problem. As for the LBED (laser beam enhancement device), I will probably rent one. I'm keeping expenses low and profit high right now. Gotta get a good cash flow before I can spend. I'm sure everyone here understands that
.
Thanks,
Jonathan
" 15 characters"
Last edited by Laser Wizardry; 11-13-2015 at 11:38.
Hey, I talked to the man in charge and basically told him that the small amount of fog or haze solution I would use, would not be enough to damage anything. He seemed a little hesitant still, but I think he was pretty convinced. I will make sure to write up a contract protecting me from liability if they DO want fog. Otherwise it will be a graphics show only. Thanks for the advice guys, still open for comments if anybody wants to add their 2 cents.
Thanks,
Jonathan
Since it seems we're back on the topic of hazers again, can anyone recommend a water-based hazer around $500? Does anyone here have any experience with the Chauvet Arena Hazer?
I have tried the Chauvet Arena Hazers a couple of times but was not impressed. They look better built in the pictures than they really are. Take a look at http://www.gearsource.com/index.cfm I bought a reconditioned Jem/Martin ZR24/7 from them a few months ago for around $500.00 works great and less than half of the price of a new unit.
Jim