Page 1 of 3 123 LastLast
Results 1 to 10 of 26

Thread: You're not allowed to laugh.

  1. #1
    Bradfo69's Avatar
    Bradfo69 is offline Pending BST Forum Purchases: $47,127,283.53
    Join Date
    Jul 2010
    Location
    Wilmington, DE
    Posts
    6,207

    Default You're not allowed to laugh.

    O.k., maybe a little but, at least I prefaced it before posting.

    I'm trying to diagnose a laser. A cheap chinese laser at that. My first. So there's some sentimentality. Stop laughing! I wouldn't really care too much but, I have a DJ friend who has been planning on buying it for home use and, it's not happy at the moment. It's a Meierlight - approximately 220mW and a couple years old. I fired it up this afternoon because it occurred to me that last time I had it out, it was only playing the built in DMX frames and not outputting an ILDA signal. I wanted to investigate that a little further plus, I needed to re-solder the internal mic leads since I clipped them putting the cover back on.

    So anyway, plugged 'er in and turned on the power. A bit of high pitched whine ensued briefly. Turned it off, waited a sec, turned it back on and now, the power sort of surges with quick bursts at a regular, repetitive cycle. Click on, click off, click on, click off. The case fan starts to spin and stop, spin and stop, the lasers light up and turn off, light up and turn off. Almost like the tick of a metronome. Power on, power off, power on, power off. My first suspect thing is the power supply. First thing in the chain right? I'm willing to throw a few bucks at replacing the supply, just for the learning experience. If it's not that, then perhaps the next step will be trying to wire in a new ILDA breakout board. I've got a bunch laying around. Stop laughing damnit! So, my initial problem is figuring out what in the hell I'm looking for when trying to find a new power supply. Pic's of the existing one are attached.

    IMGP4831.JPG IMGP4832.JPG IMGP4833.JPG IMGP4834.JPG IMGP4835.JPG IMGP4836.JPG IMGP4837.JPG

    That's assuming you all think it is the supply. Yeah... I know. Why waste the time or the money? Truth is, it wasn't a bad little projector for beginner bedroom/basement use. And, quite honestly, I need to get my hands dirty with this stuff and, learning on a couple hundred dollar piece of crap versus making a mistake with a $1000 set of scanners or, 640nm module is a bit more palatable. And, two years ago it WAS a $600 investment bundled with Moncha 2.1.

    So, am I on the right track thinking power supply? Or, is there something else probably suspect instead?

    I still HEAR you snickering... go ahead. I can take it.

  2. #2
    Join Date
    Jul 2006
    Location
    Connecticut, USA
    Posts
    2,478

    Default

    Sounds to me like Dc power supplies. This is exactly what happens with the power supplies for the 40W's when they freak out. I woul try to undo 1 DC supply at a time. See if you can eliminte the troublesome one. start with the scanners PS.

    Wait- is it 1 supply for everything?
    http://www.laserist.org/images/ildalogos/ILDA-logo_colored-beams_Corporate_150w.jpg

    ILDA- U.S. Laser Regulatory Committee

    Authorized Dealer for:

    • Pangolin Laser Software and Hardware
    • KVANT Laser Modules & Laser Systems
    • X-Laser USA
    • CNI Lasers
    • Cambridge Technology & Eye Magic Professional Scanning Systems

    FDA/CDRH Certified Professional LuminanceRGB Laser Light Show Systems


  3. #3
    Bradfo69's Avatar
    Bradfo69 is offline Pending BST Forum Purchases: $47,127,283.53
    Join Date
    Jul 2010
    Location
    Wilmington, DE
    Posts
    6,207

    Default

    Quote Originally Posted by gottaluvlasers View Post
    Sounds to me like Dc power supplies. This is exactly what happens with the power supplies for the 40W's when they freak out. I woul try to undo 1 DC supply at a time. See if you can eliminte the troublesome one. start with the scanners PS.

    Wait- is it 1 supply for everything?
    Yes, just the one supply. Everything kind of goes into that harness.

  4. #4
    Join Date
    Jul 2006
    Location
    Connecticut, USA
    Posts
    2,478

    Default

    replace it.

    only thing is, it is most likely a dual (or even triple) output supply. 5V for lasers. 12 (or 24) for the scanners. Does it have any output markings on it?
    http://www.laserist.org/images/ildalogos/ILDA-logo_colored-beams_Corporate_150w.jpg

    ILDA- U.S. Laser Regulatory Committee

    Authorized Dealer for:

    • Pangolin Laser Software and Hardware
    • KVANT Laser Modules & Laser Systems
    • X-Laser USA
    • CNI Lasers
    • Cambridge Technology & Eye Magic Professional Scanning Systems

    FDA/CDRH Certified Professional LuminanceRGB Laser Light Show Systems


  5. #5
    Bradfo69's Avatar
    Bradfo69 is offline Pending BST Forum Purchases: $47,127,283.53
    Join Date
    Jul 2010
    Location
    Wilmington, DE
    Posts
    6,207

    Default

    Quote Originally Posted by gottaluvlasers View Post
    replace it.

    only thing is, it is most likely a dual (or even triple) output supply. 5V for lasers. 12 (or 24) for the scanners. Does it have any output markings on it?
    Nope. That's a reason I included the pictures to see if anyone else recognized it. I just sent a e-mail to Meierlight along with the photo. Hopefully someone there can point me in a right direction. I don't want to spend mad money to fix this but, if I can sort it out for like $50, I'm cool with that.

  6. #6
    Join Date
    Jul 2006
    Location
    Connecticut, USA
    Posts
    2,478

    Default

    plug the supply in by itself. without the harness attached. then meter the outputs.
    http://www.laserist.org/images/ildalogos/ILDA-logo_colored-beams_Corporate_150w.jpg

    ILDA- U.S. Laser Regulatory Committee

    Authorized Dealer for:

    • Pangolin Laser Software and Hardware
    • KVANT Laser Modules & Laser Systems
    • X-Laser USA
    • CNI Lasers
    • Cambridge Technology & Eye Magic Professional Scanning Systems

    FDA/CDRH Certified Professional LuminanceRGB Laser Light Show Systems


  7. #7
    Bradfo69's Avatar
    Bradfo69 is offline Pending BST Forum Purchases: $47,127,283.53
    Join Date
    Jul 2010
    Location
    Wilmington, DE
    Posts
    6,207

    Default

    Thanks. I'll give that a shot tomorrow. It's at work in my office. I should have some free time in the morning to futz with it.

  8. #8
    Join Date
    Apr 2008
    Location
    New Orleans
    Posts
    288

    Default

    I'm not laughing. I had the same problem with a shinp rgv projector.

    The lasers flash on/off and the scanner mirrors slammed back and forth. The problem with mine was a grounding issue. The metal base plate used for an optical table was mounted with metal screws with plastic washers/shims to isolate the plate from the projector case. Over time from moving the projector around, the screws/shims got out of alignment and shorted the metal plate to the metal case. The diode cases are + and when grounded caused problems for the power supply. I replaced them with nylon screws & nylon nuts - problem solved.

    Hope yours is an easy fix too.
    Eric in New Orleans

  9. #9
    Join Date
    Oct 2006
    Location
    Cleveland, Ohio
    Posts
    2,342

    Default

    When the large black capacitor says right on it O-SHI...


    you know where to look
    Last edited by drlava; 03-12-2012 at 23:28.

  10. #10
    Join Date
    Sep 2009
    Location
    Mexico
    Posts
    475

    Default

    One of my satellites start to do the same last year. I change the PS of the galvos and Presto.

    Just my 2 cts.
    Cheers,
    Ed

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •