Page 1 of 3 123 LastLast
Results 1 to 10 of 28

Thread: Dual red very dim. refocusing needed?

  1. #1
    Join Date
    Jul 2010
    Location
    Netherlands
    Posts
    3,322

    Question Dual red very dim. refocusing needed?

    So after my scan angle once halved and my blue stopped working of my first ever laser projector I finally re-organised the wiring and fixed the ilda connector (where bad connections where the cause of the problems) and also shrink tubed all connections to the DB25 connector.

    Having "almost" all problems fixed (Blue works again, scan angle is full again) I have 1 problem left: My red.

    It modulates well and blanking works fine but it's very dim.
    Here is a picture of it:


    The driver is Die4Drive and I believe these are 2 650nm diodes.
    Adjusting the pots carefully does make a little difference in intensity but not by a whole lot it's still very dim.
    I'm assuming is not that it's a power problem but a focus problem (see the pictures below why I think this is the problem) It could also be a power problem though (I'm about to measure the psu for red with my multimeter).

    Here a few pictures:



    *The red in this picture below is coming from the lighting in my room, I have the projector off when I took this picture


    Any idea's what to do?

    Edit: Measured the psu voltage going to the driver.
    It's 3.587 Volts *when the PSU is completely turned up*
    Last edited by masterpj; 03-30-2013 at 07:00. Reason: Measured with multimeter

  2. #2
    Join Date
    Feb 2008
    Location
    East Sussex, England
    Posts
    5,248

    Default

    That looks like it might've blown and gone LED on you
    If you have to replace the diodes it might be worth looking at a pair of the 170mW 638 single mode jobbies (62388 or something like that, I think Francesco sells them nearest to you) if they'll fit in the mounts you have. Are those 5.6mm barrels?

    What is the power and wavelength of the green and blue in the projector?
    Frikkin Lasers
    http://www.frikkinlasers.co.uk

    You are using Bonetti's defense against me, ah?

    I thought it fitting, considering the rocky terrain.

  3. #3
    Join Date
    Jul 2010
    Location
    Netherlands
    Posts
    3,322

    Default

    Quote Originally Posted by norty303 View Post
    That looks like it might've blown and gone LED on you
    If you have to replace the diodes it might be worth looking at a pair of the 170mW 638 single mode jobbies (62388 or something like that, I think Francesco sells them nearest to you) if they'll fit in the mounts you have. Are those 5.6mm barrels?

    What is the power and wavelength of the green and blue in the projector?
    Wavelength blue: 473nm
    Wavelength Green: 532nm

    Powers I don't have but my estimate is 300~400mw green and 180~250mw blue.
    It don't need high powers for the projector so thats fine I want to use this as a extra graphic projector.

    edit: Measured the diameter myself and its 0.432inches or 10.97mm
    Last edited by masterpj; 03-30-2013 at 08:44. Reason: measured barrel diameter

  4. #4
    Join Date
    Jan 2012
    Posts
    291

    Default

    Pj, you could also buy a 3.8mm diode house from Dave, fit in a single mode 120mw Opnext (you can overdrive it to 150/175, i tested it last week and it hit 290mw) costs would be less then € 100,-
    Or you could buy a 5.6mm diode house from Dave and fit in a 300mw multimode 638 Mitsubishi also less then € 100,- euro's.
    I have both sets over here if you want to try, just give me a message.
    Just be aware that the beam hight would be 29mm with Dave's mounts.

  5. #5
    Join Date
    Jul 2010
    Location
    Netherlands
    Posts
    3,322

    Default

    Quote Originally Posted by astatic View Post
    Pj, you could also buy a 3.8mm diode house from Dave, fit in a single mode 120mw Opnext (you can overdrive it to 150/175, i tested it last week and it hit 290mw) costs would be less then € 100,-
    Or you could buy a 5.6mm diode house from Dave and fit in a 300mw multimode 638 Mitsubishi also less then € 100,- euro's.
    I have both sets over here if you want to try, just give me a message.
    Just be aware that the beam hight would be 29mm with Dave's mounts.
    Thanks! Will most certainly consider that.
    Was considering to get 2 new diodes on ebay though.
    I bet I would need to get a new collimator and housing that would fit, as it doesn't seem like I will be able to get these diodes out of their barrel (correct me if I'm wrong).

    Reasons is that money is tight at the moment and I'm fine with a temporary solution that works. *damn u expensive retro equipment*
    I'd also prefer to stick with the current mounts I have, so I wont have problems with difference in beam height.

    Edit: looking at the barrels I might be able to get these diodes out of their barrels and put in a new one
    Last edited by masterpj; 03-30-2013 at 08:48. Reason: barrels

  6. #6
    Join Date
    Jul 2010
    Location
    Netherlands
    Posts
    3,322

    Default

    was able to successfully extract the diodes from their housings.

  7. #7
    Join Date
    Jan 2012
    Posts
    291

    Default

    Pj most of the time they are pressed into the barrel, difficult to get them out because they need a good thermal contact.
    As far as i see on the picture which you took from the front of the barrel you could unscrew the copper front to get out the lens so you won't have to buy a new one.
    Maybe you could press out the diode from the front, just give it a try or just drill it out with a 3mm drill if the diodes are 5.6mm, you will loose the diode but safe the barrel with the lens and you only have to buy a new diode.
    Before replacing the diode be sure the driver fits the right current and don't forget to short cut the driver (when the power is off) or you would end up with another led (this was a good warning a while ago from dimitri)

  8. #8
    Join Date
    Jan 2012
    Posts
    291

    Default

    I'll sponsor you a 5.6 Mitsubishi 300mw if you want, you only have to pick it up
    I have to go to the swimming pool in about 15 minutes, i'll leave it in the mailbox so you could go on if you want!
    Just show us the results.

  9. #9
    Join Date
    Oct 2010
    Location
    Athens, Greece
    Posts
    1,930

    Default

    well, as you are mostly into graphics yourself, I would sugest 660nm LOC (the dvd sort of thing) diode plus a single mode opnext 110mw, so you'll get a wider pallet

    I think the mitsu 300mw will be to much of a flashlight for your taste (plus it will require correction optics)
    "its called character briggs..."

  10. #10
    Join Date
    Jul 2010
    Location
    Netherlands
    Posts
    3,322

    Default

    Thats very awsome of you!
    Also I had not that much trouble getting both diodes out
    tumblr_mkhemx3O611r95qbjo2_500.jpg
    I think I can pick up the diode tomorrow I have to finish up a bit of work.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •