Page 1 of 4 1234 LastLast
Results 1 to 10 of 34

Thread: Buying first RGB laser

  1. #1
    Join Date
    Jun 2013
    Location
    Sydney, Australia
    Posts
    244

    Question Buying first RGB laser

    I am looking to buy a laser for an art project I am doing, I have been offered an older Laserworld RS-1700RGB, or am looking at a CS2000RGB SE with the 50k scanner upgrade, both can be bought for around the £1500 mark. Which is the better laser? I would actually prefer an analogue one but my budget may prevent that . Another option is an NRG5000 RGB, whilst this is analogue and I appreciate more power, it looks to have slower scanners installed. Does anyone have any experience or advice on these models or anything else I should look at?

    Thanks in advance.

  2. #2
    Join Date
    Jun 2011
    Location
    GuangZhou, China
    Posts
    273

    Default

    How about this one: http://www.topiclight.com/en/disproduct.php?id=83

    will PM you if you needed.

    Tks!
    Song
    L.A.S.E.R.
    Light Amplification by Stimulated Emission of Radiation

    Laser system: Pure Diode 3W & 6W RGB Laser.



    www.facebook.com/saifer.sy
    www.laser-viva.com

  3. #3
    Join Date
    Jan 2013
    Location
    Detroit, USA
    Posts
    558

    Default

    Laserworld is garbage, save your money.

  4. #4
    Join Date
    Dec 2010
    Location
    Netherlands/Holland ;)
    Posts
    190

    Default

    Hi Steviobee,

    I have a G-tech that i converted from 200mW green to RGB (300mw-637nm, 180mw-532nm, 600mw-445nm) analogue with DT30 in it. I can put a 600mw green in it for you so the balance is a bit better.

    Here some more info:
    http://www.photonlexicon.com/forums/...-RGB-Projector

    With the new green i'm aiming around 1500 euro.

    Don't know if it fits you needs.

  5. #5
    Join Date
    Jun 2013
    Location
    Sydney, Australia
    Posts
    244

    Default

    Quote Originally Posted by Song View Post
    How much are these Song?

    Quote Originally Posted by Stiffler View Post
    Laserworld is garbage, save your money.
    Why do you say that? I read alot on here about not living up to stated figures but I'm thinking about buying through a dealer so service should be better? And 12 months warranty...

  6. #6
    Join Date
    Jan 2013
    Location
    Detroit, USA
    Posts
    558

    Default

    Quote Originally Posted by steviobee View Post



    Why do you say that? I read alot on here about not living up to stated figures but I'm thinking about buying through a dealer so service should be better? And 12 months warranty...
    This is not about service, this is about performance. Laserworld flat out lies about the power of their lasers, and the CS2000RGB is not a very well built machine (and it's not very bright, considering it's rated power). However, if you are getting it cheap enough (that price seems high) it might be worth buying just for the scanners; once you get bored with it you can always upgrade the laser modules (although it's a pretty tight fit).

    -Eric

  7. #7
    Join Date
    Aug 2007
    Location
    Under a rock in Cambridge UK
    Posts
    1,353

    Default

    Quote Originally Posted by steviobee View Post
    with the 50k scanner upgrade
    Laserworld 50k scanners are not 50k as the ILDA standard defines. They will not display the ILDA test pattern at 8 degrees, 50k... I have two sets as spares and after many, many hours of serous tuning, the best they will achieve is 28k, and even that is really pushing them to the absolute limit...

  8. #8
    Join Date
    May 2008
    Location
    Once it was called "Bel Paese" = ITALY
    Posts
    858

    Default

    Quote Originally Posted by Insanity View Post
    Laserworld 50k scanners are not 50k as the ILDA standard defines. They will not display the ILDA test pattern at 8 degrees, 50k... I have two sets as spares and after many, many hours of serous tuning, the best they will achieve is 28k, and even that is really pushing them to the absolute limit...

    I quote and I agree. Absolutely.

    Me too have a couple of them.
    At 10 degrees angle, when you're approaching to 26-27Kpps, they start to scream like... wounded eagles!
    Best I obtained has been 28Kpps at 5-6 degrees.
    And then... mirrors also are not so good (a discrete amount of losses).
    my webpage
    http://stevemilani.jimdo.com
    Skype ID: stevemilani957

    my RGB analogue projectors:
    3.9 W (640/532/445) 30kpps
    2.6 W (655/532/450) 30kpps
    2.5 W (638/532/450) 30kpps
    0.7 W (test unit)(635/532/473) 18kpps

  9. #9
    Join Date
    Jun 2013
    Location
    Sydney, Australia
    Posts
    244

    Default

    Enough said as far as laserworld goes then, is this the same for their other products they sell like SwissLas or RTI? Although too expensive for me!

    And what about an NRG5000 RGB, i've been told by guys on this forum about their beam divergence, etc but is that a sacrifice if bought for a good price?

    I must say I am very tempted by goldenstarlaser's offerings but am worried about shipping from China to the UK, warranty, etc....

  10. #10
    Join Date
    Aug 2007
    Location
    Under a rock in Cambridge UK
    Posts
    1,353

    Default

    Swisslas and RTI are very nice projectors, but like you say, very expensive... Ya gets what ya pays for...

    Stanwax in the UK do good quality projectors at reasonable prices and Rob is a member here... Depending on your budget, you could look at Synchrovision (Kvant) I think they are based pretty close to you... I also hear good things about Golden Star, I bought some components from them and the shipping was very fast...

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •