Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 34

Thread: Buying first RGB laser

  1. #21
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,836

    Default

    use this: http://www.pangolin.com/userhelp/scanangles.htm

    Quote Originally Posted by steviobee View Post
    How can I tell in QS?
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

  2. #22
    Join Date
    Jun 2013
    Location
    Sydney, Australia
    Posts
    244

    Default

    Thank you! Will have to check it out tomorrow now, but what is the best way to adjust?

    Quote Originally Posted by swamidog View Post
    Last edited by steviobee; 07-03-2013 at 14:43.

  3. #23
    Join Date
    Jun 2013
    Location
    Sydney, Australia
    Posts
    244

    Default

    From my measurements I make the angle 18 degrees?


    Quote Originally Posted by swamidog View Post
    what's your scan angle?

  4. #24
    swamidog's Avatar
    swamidog is offline Jr. Woodchuckington Janitor III, Esq.
    Join Date
    Nov 2006
    Location
    santa fe, nm
    Posts
    1,545,836

    Default

    that's a pretty broad scan angle. reduce it to about 8 degrees and see what happens.

    Quote Originally Posted by steviobee View Post
    From my measurements I make the angle 18 degrees?
    suppose you're thinkin' about a plate o' shrimp. Suddenly someone'll say, like, plate, or shrimp, or plate o' shrimp out of the blue, no explanation. No point in lookin' for one, either. It's all part of a cosmic unconciousness.

  5. #25
    Join Date
    Jun 2013
    Location
    Sydney, Australia
    Posts
    244

    Default

    Quote Originally Posted by swamidog View Post
    that's a pretty broad scan angle. reduce it to about 8 degrees and see what happens.
    I still am having a lot of flicker on many of the cues and also on the QS test image (one with 'Top' at the top) as well as others. I have reduced the scan angle in QS to equal 8 degrees (23% x 23%) and have gone down to 10% x 10% in the image size box? If I reduce the scan rate in QS it gets worse, It is set at 30PPS max. The cues with the problem have the FPS going down to below 30?
    Am clueless what to do now, surely the 'TOP' test image should be flicker free at 8 degrees?

  6. #26
    Join Date
    May 2008
    Location
    Once it was called "Bel Paese" = ITALY
    Posts
    858

    Default

    This is the way I used to find the right angle (example: 30° projection angle)

    1) Put the projector infront of a wall.
    2) Measure exactly (or best you can) 1 meter horizzontal distance between scanners mirrors and the wall.
    3) Set 100% of "Y" and "Y" size by QuickShow.
    4) Draw a simple square figure which fit exactly all the window frame editor of QS.
    5) For best scanners safety, set low scanspeed (15-18kpps) and then measure each side of square figure projected on the wall.
    If each side of square measure 53.6 centimetres (millimeter more or less)... you have just found 30° degrees scan angle and you also know that this angle match with the maximum opening of scanners (100%)

    See the angle data table for more values.
    http://www.pangolin.com/userhelp/scanangles.htm

    Repeat, step by step, same way to check the maximum scan angle that DT40pro allows you (60°). When at 1 meter, you should have 115.5 centimeters on each side of square. If needed (almost sure) reduce scanspeed once more.
    my webpage
    http://stevemilani.jimdo.com
    Skype ID: stevemilani957

    my RGB analogue projectors:
    3.9 W (640/532/445) 30kpps
    2.6 W (655/532/450) 30kpps
    2.5 W (638/532/450) 30kpps
    0.7 W (test unit)(635/532/473) 18kpps

  7. #27
    Join Date
    Jan 2013
    Location
    Detroit, USA
    Posts
    558

    Default

    Besides the scan issue, how does the laser perform (beam quality, etc)? I bought 2 of these lasers in the new smaller case, they should be here by the beginning of next week. Once they arrive I'll test both of them, and we can compare our results.

    -Eric

  8. #28
    Join Date
    Jun 2013
    Location
    Sydney, Australia
    Posts
    244

    Default

    Quote Originally Posted by Steve Milani View Post
    This is the way I used to find the right angle (example: 30° projection angle)

    1) Put the projector infront of a wall.
    2) Measure exactly (or best you can) 1 meter horizzontal distance between scanners mirrors and the wall.
    3) Set 100% of "Y" and "Y" size by QuickShow.
    4) Draw a simple square figure which fit exactly all the window frame editor of QS.
    5) For best scanners safety, set low scanspeed (15-18kpps) and then measure each side of square figure projected on the wall.
    If each side of square measure 53.6 centimetres (millimeter more or less)... you have just found 30° degrees scan angle and you also know that this angle match with the maximum opening of scanners (100%)

    See the angle data table for more values.
    http://www.pangolin.com/userhelp/scanangles.htm

    Repeat, step by step, same way to check the maximum scan angle that DT40pro allows you (60°). When at 1 meter, you should have 115.5 centimeters on each side of square. If needed (almost sure) reduce scanspeed once more.
    Thanks Steve, will try this as well, does yours flicker at these settings, I will use the 'Top' test image square? Mine seems to always flicker whatever size I have it at?

    Quote Originally Posted by Stiffler View Post
    Besides the scan issue, how does the laser perform (beam quality, etc)? I bought 2 of these lasers in the new smaller case, they should be here by the beginning of next week. Once they arrive I'll test both of them, and we can compare our results.

    -Eric
    On the whole a great unit, seems very powerful, nice white when the blue is dropped down a bit, red seems a little large and my X-axis is reversed? If the fans were quieter and the flickering was sorted though...!

    Yes be good to hear how you get on with yours...

  9. #29
    Join Date
    Dec 2007
    Location
    NorCal / Western Caribbean
    Posts
    710

    Default

    Can you post some pictures please

    Cheers
    Rich

  10. #30
    Join Date
    Nov 2011
    Location
    Bedfordshire, UK
    Posts
    603

    Default

    Hi Steve.

    Ummm... if QS is showing a low FPS number it could be that your control computer is struggling to process things quickly enough... I think.
    I get similar flikering when running QS with other stuff open in the background, but usually only when running both my FB3 as seperate images.
    I may be waayy off here, but try closing all other programs and background running aps like the funky Windows Desktop etc and see if that helps?
    At the very least it'll rule out a factor...
    If in doubt... Give it a clout?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •