Page 1 of 6 12345 ... LastLast
Results 1 to 10 of 55

Thread: PT-40k(60k) Scanner Set

  1. #1
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default PT-40k(60k) Scanner Set

    What's your guys opinion on the PT-40k scanners?

    Technical details:

    -Deflection angle: max. 70° optical
    -Scanspeed: up to 60,000pps with 6 x 10mm mirror
    -Input: Analog +/-5V
    -Power: +/- 24VDC @ 1A

    60,000pps @ 5°
    50,000pps @ 8°
    40,000pps @ 20°

    http://spacelas.com/html_products/60...l#.Uk3wi4asiSo

  2. #2
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    From personal experience... You are getting a 40K scanset. Forget 50 and 60K... never going to happen. You are going to get 40K at about 8° +/- depending on tuning and 30K at 10°~14°. If you push them any wider than that, the polyswitch is going to kick in and limit the amp which requires a power cycle to reset. I don't do commercial shows so mine don't get used that much but I have retuned mine for 30K and they work fine for low scan angle. They don't hold a candle to my DT-40pros but they are not as expensive either.
    If you're the smartest person in the room, then you're in the wrong room.

  3. #3
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    Well the majority of my stuff is overhead beam shows and i run at the widest angle i can in the software.

    Im assuming they will get the job more than done?

  4. #4
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    Quote Originally Posted by absolom7691 View Post
    From personal experience... You are getting a 40K scanset. Forget 50 and 60K... never going to happen. You are going to get 40K at about 8° +/- depending on tuning and 30K at 10°~14°. If you push them any wider than that, the polyswitch is going to kick in and limit the amp which requires a power cycle to reset. I don't do commercial shows so mine don't get used that much but I have retuned mine for 30K and they work fine for low scan angle. They don't hold a candle to my DT-40pros but they are not as expensive either.
    Haha i was told the other way around lol

  5. #5
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    There's a reason why PT-40s are under $400 dollars shipped. They are a good scanner for graphics at angles less than 20°. Trust me, I have retuned mine for 30K and I can't hit 20° without triggering the polyswitch. If you look at the specs for these and the specs for the DT-40s, you will see that the DTs have much more realistic specs. I am running my PTs for graphics and not beams but I can't see the angle going up too much for beams without triggering a shut down. The only two scansets I know of that will hit wide angles at decent speeds are the DT-40 wides and the EMS-4000 scanners. If you were to retune these for 20~25K, you might be able to scan at wide angle.
    If you're the smartest person in the room, then you're in the wrong room.

  6. #6
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    I dont like the thought of a shut down, mid show that would be a disaster...

    I guess to circumvent this i could project the ilda pattern and full angle in the software, adjust the scan rate until it projects correctly(regardless of flicker), and set a max scan rate in beyond. That way i dont have to worry about over driving them and popping that switch?

  7. #7
    Join Date
    Apr 2010
    Location
    Grand Rapids, Mi
    Posts
    2,538

    Default

    Quote Originally Posted by JD3 View Post
    I dont like the thought of a shut down, mid show that would be a disaster...

    I guess to circumvent this i could project the ilda pattern and full angle in the software, adjust the scan rate until it projects correctly(regardless of flicker), and set a max scan rate in beyond. That way i dont have to worry about over driving them and popping that switch?
    Or buy real galvos serious if your doing shows for
    Money Cambridge or Eye Magics are your best friends
    leading in trailing technology

  8. #8
    Bradfo69's Avatar
    Bradfo69 is offline Pending BST Forum Purchases: $47,127,283.53
    Join Date
    Jul 2010
    Location
    Wilmington, DE
    Posts
    6,207

    Default

    I need to perhaps mention ( and I could be TOTALLY wrong here) that there may be two scanners manufactured out there with the same name. Not unlike the name "X-Laser" being used by a couple companies. Spacelas has the PT-40s but, I understand that Lightspace manufactures their own scanners which are also named "PT"-followed by a number.

    Just making sure it's an apples to apples answer. I'll go away now. (Since I can't intelligently speak to the testing of them.)

    (But I'll ditto polishedballs answer...if it's critical or real money is involved go EM or Cambridge.)

  9. #9
    Join Date
    May 2007
    Location
    1 hr from everything in SoCal
    Posts
    2,833

    Default

    Quote Originally Posted by JD3 View Post
    I dont like the thought of a shut down, mid show that would be a disaster...
    Quote Originally Posted by polishedball View Post
    Cambridge or Eye Magics are your best friends
    ^^^^ What he said. I have heard of EMS-4000s (Eye Magic) being pushed at crazy wide scan angles.
    If you're the smartest person in the room, then you're in the wrong room.

  10. #10
    Join Date
    Aug 2013
    Location
    Houston
    Posts
    537

    Default

    Quote Originally Posted by polishedball View Post
    Or buy real galvos serious if your doing shows for
    Money Cambridge or Eye Magics are your best friends
    I dont charge enough for shows to afford those

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •