To help reinforce the answers others have given to the OP, the safety limits for laser light exposure are quoted in either 'power per area' (irradiance) or 'energy per area' (radiant exposure). For ease of simplified measurement, it is often more convenient to consider exposure in terms of the first quantity, 'irradiance'. (the way to remember what 'irradiance' is, is to think 'power density'; i.e. how strong the light is concentrated on a particular area)
What the Pangolin Safety Lenses do is alter (weaken) the power density of laser beams passing through them, not the power. Different strengths of lens can be used to vary how much the original beam is modified. The lens is a semicircle, so that it can be used on a single laser projector output window to modify the lower half, (usually), of the scan field area. i.e. the bit where the spectators are present.
Why not just modify the whole output window? Well you could, and Pangolin do offer a complete circle lens option now as well. But because the lens increases the spread of the beam achieve the lower power density, the resulting beam can look fatter and fuzzier, loosing the crispness that people associate with lasers. So it is often desirable to have tight unmodified beams overhead, and just modify the beams that can hit the spectators.
So to outline the process required to check if exposure will be safe you have to:
Decide on the 'applicable MPE', which is a maximum power density that is permitted.
Check the exposure using a meter at the closest point of contact with spectators, and adjust with the lens to have a power density reading lower than the MPE limit.
To perform step 2, it is easiest to do this, (instrumentation wise), with a laser power meter designed to measure stationary beams, which is why it useful to convert the MPE exposure limits to irradiance, (power density).
Adjusting the power density of a laser beam by increasing its size is far more effective than just adjusting it by turning the power down.
Norty was correct in saying that value for the limit is 2.5mW per square centimetre, 'in the absence of any other controls' - this is important. And I therefore want to reemphasise the point made earlier by others. If you do not have a scan-fail that can limit the output, then you cannot justify using higher irradiance than 2.5mW per square centimetre. In fact the UK guidance on the issue states that in the case of persons likely to under the influence of alcohol or drugs, a more conservative limit of 1mW per square centimetre should be used as the limit. This is because these people will not have a normal aversion response, so this can't be relied upon as a way of controlling exposure duration.
The continuous exposure limits noted above are consistent with IEC's international guidance for laser show safety (IEC/TR 60825-3:2008), that was primarily authored by John O'Hagan with the assistance of ILDA, and published in 2008.
So in terms of power through a 7mm circular aperture, we are still talking about a 1mW 'power' reading being the equivalent to a 2.5mW per square centimetre irradiance. And similarly, 0.38mW being the equivalent to a 1.0mW per square centimetre irradiance.
(The latest laser safety limits published by ICNIRP now additionally state the visible MPE in terms of the 7mm aperture as it's such a useful way to quote MPE. It overcomes the IEC-ANSI difference in quoting 'per m' and 'per cm', which can cause some further confusion. I've used the 'per cm' units in this post to be consistent with earlier posts in the thread, but virtually everywhere outside of the US uses 'per m'. 25.4W per square metre is the same as 2.5mW per square centimetre)
The MPE is not a fixed figure, it is time dependent, so the shorter amount of time you are exposed to light, the more light you can be exposed to. Conversely, if you are are exposed to light for longer periods, the amount of light you can be exposed to decreases. Only if there scanning safeguard present should greater irradiance values be applied.
As Bill has stated, if exposures can be assured to be less than 1ms in duration, then a valid argument can be made to defend the use of the higher MPE.
However, it may seem fine to say that a scanning failure of a scanning beam that has its light limited to a fixed maximum irradiance, only exceeds the MPE by 4x etc in the case of a drastic scanner movement failure. But from my experience with venues and insurance companies, they are not interested in 'any' MPE excess being a possibility.
Science and risk aside, the key figure is the excess. Being 4x or 10x above the legal limit sounds bad in an insurance claim or court room. End of. Especially if what lead to the exposure goes against published international guidance on the subject, or poor safety control measures. The organisations I have in my work portfolio would not be interested in being in position where they are having to defend even a 4x the limit claim. Such a situation makes it easy pickings for a claimant seeking compensation, likely resulting in an out of court settlement by the insurance company. - this is not speculation, I've seen, firsthand, this happen when an organisation's lack of controls, have lead to a strong likelihood of exposure levels being exceeded.
So, while Bill is right to state that a 5mW reading is acceptable on a Lasercheck, it must always be used with a good robust scanning health monitor, that can limit duration. To be defendable, this should be something that monitors more than just scanner velocity. And really, when using increased light levels that push the extent of the shorter exposures, to get brighter beams, greater care has to be taken to make sure the limits are not being exceeded.
The limits are one thing, but for some time, more recently, John O'Hagan has been expressing concerns about deliberate spectator exposure, and has evidence to suggest that a further, (reducing), correction factor should be applied to account for visual disturbance from direct ocular exposure. This was a hot topic discussed at last year's ILSC meeting, and I guess will continue as time moves on.
One thing with laser safety is that it is a fluid subject, and as scientific knowledge grows, the limits and how exposures are considered evolve too. Hence the reason for the exposure limits being updated last year, and finding their way into the safety standards due to be published shortly.
Hopefully this has helped to answer the OP's question, and to provide some more detail to others that are interested in this topic and the rationale for the figures being quoted.
James


Reply With Quote

)
