Page 4 of 4 FirstFirst 1234
Results 31 to 39 of 39

Thread: Hey Pat....

  1. #31
    Join Date
    Jun 2007
    Location
    Lake Geneva, WI.
    Posts
    2,704

    Default

    Quote Originally Posted by Laserman532 View Post
    damn, for 11 years old, those things rock!
    How about it! I would have never guessed I'd have them that long. I've gone through three sets of lenses ( One set being Rx before I got laser eye surgery.) and 4 sets of new rubber. The frame is indestructible however. I've only dropped, smashed and crashed them over 100 times and they still look as good as new.

  2. #32
    Join Date
    Aug 2007
    Location
    Portland
    Posts
    1,355

    Default

    These are my sunglasses. They're polarized and cost $6. As you can see, they don't have much defense against my ass landing on them in the car. (I'll bend them back -again.)




    ...and, for fun, here's the view out my sliding-door window through my OD5 532nm Safety Goggles.


    -Jonathan

  3. #33
    Join Date
    Nov 2007
    Location
    Bend Oregon USA
    Posts
    3,350

    Default

    damn dude...how to you keep them from falling off your head

    duct tape I guess
    Pat B

    laserman532 on ebay

    Been there, done that, got the t-shirt & selling it in a garage sale.

  4. #34
    Join Date
    Aug 2007
    Location
    Portland
    Posts
    1,355

    Default

    Quote Originally Posted by Laserman532 View Post
    damn dude...how to you keep them from falling off your head
    I still haven't manhandled them back into their correct shape.

    -Jonathan

  5. #35
    Join Date
    Jul 2008
    Posts
    54

    Default

    Quote Originally Posted by Laserman532 View Post
    The beam combiner is a bitch to align I have one but I probably will make my own contraption.
    Hey Pat, if you want the beam combiner aligned, I can probably do that for you. If it's the LFI version (built in 1" beam tubes) there's a very good chance that I built it! I just need an hour with the combiner and the laser it mounts to.

    Did you get the mug? What do you think of the new logo? (It is almost identical to the old one.)

  6. #36
    Join Date
    Jul 2008
    Posts
    54

    Default

    Quote Originally Posted by GooeyGus View Post
    well it's stable at 1.5W now, I got it as high as 2.3W by just barely touching the LBO mount, so more alignment is in its future. I also need to get some harder glue. I'm not too satisfied with the hardness of mine after it dries, for this particular application. Its perfect for pretty much everything, but not for an output mirror. even .01mm of flex and the power goes up or down.

    EDIT: Hey pat, you dont happen to have a set of 808 goggles I could borrow, would ya? I have all the dangerous 808 spray shielded right now while I'm tinkering, but it would be nice to get my 'shields' out of the way :P
    GooeyGus -If you want to bring the laser down to my place in Mill Creek you can use my UV cure epoxy system, Laminar flow hood (Class 10 Cleanroom), and 808nm glasses. Send me a PM!

    -Alex

  7. #37
    Join Date
    Nov 2007
    Location
    Bend Oregon USA
    Posts
    3,350

    Default

    Quote Originally Posted by laseralex View Post
    Hey Pat, if you want the beam combiner aligned, I can probably do that for you. If it's the LFI version (built in 1" beam tubes) there's a very good chance that I built it! I just need an hour with the combiner and the laser it mounts to.

    Did you get the mug? What do you think of the new logo? (It is almost identical to the old one.)
    Hey alex, thanks for the offer. I have the tube alignment thing down, a pain..but functional.

    I got the mug and sent you a PM the same day if I recall...Yes I like it a lot Thanks again...How come you didnt make it to PaCoLEM II?
    Pat B

    laserman532 on ebay

    Been there, done that, got the t-shirt & selling it in a garage sale.

  8. #38
    Join Date
    Jul 2008
    Location
    Marysville, WA
    Posts
    855

    Default

    Quote Originally Posted by laseralex View Post
    GooeyGus -If you want to bring the laser down to my place in Mill Creek you can use my UV cure epoxy system, Laminar flow hood (Class 10 Cleanroom), and 808nm glasses. Send me a PM!

    -Alex
    Sweet! I'm in!

    (insert this sentence to make the post longer, and thus suitable for the 'minimum character limit' of the forum)

  9. #39
    Join Date
    Jul 2008
    Posts
    54

    Default

    Quote Originally Posted by Laserman532 View Post
    How come you didnt make it to PaCoLEM II?
    Because I work too much.

    (Re)starting a business is a F#$&*%@ pain in the backside.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •